Question about Hotpoint Washing Machines

1 Answer

LED LIGHT KEEPS FLASHING & MACHINE WONT START UP

MY WASHING MACHINE FLOODED MY KITCHEN, I TURNED OFF THE MACHINE BY THE MAINS & OPENED THE DOOR BUT WATER GUSHED OUT SO I QUICKLY SLAMMED THE DOOR SHUT & NOW THE DOOR KEY LIGHT JUST KEEPS FLASHING BUT WONT LET THE MACHINE START UP, BEEPS 5 TIMES & THATS IT & IF YOU PRESS ANY BUTTONS IT BEEPS AGAIN. ALL OTHER BUTTONS, PROGRAMS ETC LIGHT UP OK. I UNBLOCKED A THICK BLACK PIPE AT THE BACK OF MACHINE WHICH HAD LIKE A PING PONG BALL IN IT & THERE WAS BITS OF MATERIAL ETC.

Posted by on

  • PAULA MORRELL Jan 19, 2013

    I DONT HAVE A PUMP AT FRONT ON THE MACHINE, BUT I PUT MACHINE ON THE SIDE & CLEARED A THICK BLACK PIPE AT THE BACK OF MACHINE WHICH HAD A WHITE PLACTIC THING WHICH HAD HOLES IN AND ALSO HAD LIKE A PING PONG BALL SO ASSURE THIS WAS THE PUMP. MACHINE IS FLASHING 5 TIMES WITH THE DOOR KEY LIGHT KEEPS FLASHING

  • PAULA MORRELL Jan 19, 2013

    DOOR WANT LOCK SO MACHINE WONT SEND SIGNAL TO START

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 1 Answer

Have you checked the pump filter ?

Posted on Jan 17, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1294 Answers

SOURCE: wont start on any program

Close your faucet valve & unscrew your hoses to check screens on hoses & machine. Clean out well. Water from faucet shd be in good pressure. Refit, check for leaks. If this is not the problem change your inlet valve, it is easily done.

& rate me pl.

Posted on May 10, 2008

jason0110
  • 66 Answers

SOURCE: error code h20

hi sounds like a faulty fill valve easy fix

Posted on Sep 21, 2008

  • 17 Answers

SOURCE: our washing machine (Zanussi ZWF 1632 W) flashes 5 times

This is a motor problem the end light flashing 5 times indicates error E50. The motor has either got wet or has just failed i would suggest trying to dry it 1st but i would suspect the motor has gone down to earth usually having to replace it. The part no. DST1246179079 Motor aprox £195 but shop around you may find it cheeper.

Posted on Dec 17, 2008

  • 574 Answers

SOURCE: Bosch Classixx 1200 red wash light flashes but doesn't start

Could still be the water inlet valve. What you need to do is pull the washer out where you can get to the valve and the plug. Unplug the inlet valve and start the washer and when you start it as normal check the volts of the plug and see if its 110 if it is you know that the valve is getting power to open but not,replace the valve. If you dont get any voltage then it could be the relay or control board

Posted on Sep 02, 2009

  • 2 Answers

SOURCE: Ping pong ball in washing machine pipe

Yes it is ment to be in there, ive searched the internet and everyone having the same problem with a ping pong type thing, do not remove, as it used as a valve for the drain.

Posted on Jun 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Indesit IWD7145K Washing Machine Error code F06 flashing on digital display + all program indicator lights. What does this mean. There is no such error code in the troubleshooting section of the manua


F06 - Door lock fault
Issue: Washing machine door cannot be opened or closed/when the door is closed the machine the programme will not start.
Advice: If your washing machine door will not close, please check for any obstructions in the door lock.
OR,
Switch off the device. Disconnect power. Wait about 3 minutes.
Open the door, then close. Reconnect device to the network.
Start device.

Cause: Door lock fails to close / open door lock triac open / closed,
frequency signal fault

Dado

Feb 12, 2015 | Indesit Washing Machines

1 Answer

Whirlpool 6th sense wont start cycle


I have the same problem. Look at the previous post, it seems to be the motor brush worn out. I've opened up the machine and checked. The carbon brush remains very little. I am trying to find out a replacement brush

Dec 27, 2013 | Whirlpool AWM6100 Front Load Washer

1 Answer

Hello I have a washing machine EWX14440W and the green Start Pause LED light is flashing. I have cleaned the fluff filter, turned off the mains and turned it back on again, done a short dry cycle...


http://data.manualslib.com/pdf/5/461/46091-electrolux/ewx_14440_w.pdf?dabc55afaee556910dced33ebba5ef18

This is the manual on your machine. Unfortunately there is no info on the blinking light so I am assuming that it is a delayed start. Now remember this is a high efficiency machine so it may not seem like it is doing anything when it is. As far as the drying part is concerned, check your drying temp. selection.

Dec 10, 2013 | Electrolux Washing Machines

1 Answer

Why wont my machine empty out..


The problem you are having is the pressure switch, also called the water level switch.Without a model # its hard to give any real direction for repair or any part #.

May 06, 2012 | Hotpoint Washing Machines

1 Answer

Washing machine wont drain properly starts as normal then after10 /20 seconds main light just keeps flashing and machine wont respond to anything and has to be turned off at mains


Hi,

I would suspect the timer unit--it controls all functions. I would replace the lid switch as it is a safety feature.Try to pull the timer knob off--you should find several screws behind it that release the module (the top should be off).

Thanks

Sep 13, 2009 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Error code h20


hi sounds like a faulty fill valve easy fix

Sep 17, 2008 | Hotpoint Ultima WF860 Front Load Washer

2 Answers

Indesit widl 126 s washer/dryer wont drain


Ive fixed my problem by turning it on, and after it does the standard pumping part pull out the power plug. Then when you plug it in again it will completely drain and its all reset again.

Aug 28, 2008 | Washing Machines

1 Answer

Hotpoint WF210 110 Spin - drainage blocked and flooded kitchen, now start/stop light and energy light flashing. Have tried switching on and off at mains... also left it for a few hours... still doing it....


Check your exit hose spigot, it may be clogged. This is if your filter is all clean (ref manual) There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it (maximum 7 inches). Snaking out your standpipe & drain is imperative.

Jun 04, 2008 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

452 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

puggy666

Level 1 Expert

48 Answers

freddyfox

Level 2 Expert

236 Answers

ptpumpman

Level 3 Expert

407 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...