Question about Onkyo HTR500 Receiver

1 Answer

Jvc reciever turns on and then shuts off with overload

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Disconnect all speakers and inputs and try again. If it stays on, you have a short in one of the connections. Try adding them one at a time and see if it shuts off.
If it overloads with nothing connected, you have an internal problem.

Posted on Jan 16, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My jvcMXGT90 keeps shutting off the audio keeps shutting off when ever the jvc is cranked past 15 and the bass is on levle four what should udo??


Turn it down or it will turn itself down permanently.

http://www.retrevo.com/support/JVC-MX-GT90J-manual/id/314ci360/t/2/

Read the paragraph labeled "CONNECTION" on Page 2 of the SP-MXG70 (last) part of the document.

Generally speaking, an amp attempts to protect itself from heat, shorts, overloads and operator exuberance by refusing to turn on or stay on.

Overloads can be from excessive periods of high output or marginally low impedance loading by the speakers; and shorts would be wiring issues or a speaker blowing up.

Aug 24, 2011 | JVC MX-GT90 CD Shelf System

1 Answer

My reciever plays then cuts out


They don't overload from missing speakers. I'm curious, what buggered the one speaker?

Examine all of your speaker wires carefully to be sure no unintended contact is made between them and anything else.

Is "overload" being displayed?

“OVERLOAD” starts flashing on the display.

Speakers are overloaded because of high volume.

1. Press STANDBY/ON on the front panel to turn off the receiver.
2. Stop the playback source.
3. Turn on the receiver again, and adjust the volume.
----------------
Speakers are overloaded because of short circuit of speaker terminals.

Press STANDBY/ON on the front panel, then check the speaker wiring.

If “OVERLOAD” does not disappear after turning on the receiver again, unplug the AC power cord, then plug it back in again.
If speaker wiring is not short-circuited, contact your dealer.

Mar 31, 2010 | JVC RX-6042 Receiver

1 Answer

I get my receiver to about 65% volume and it turns off


Check the ohm load for the reciever, then check to see what ohms are of the speakers. make sure they match. 4ohm to 4ohm, 8ohm to 8ohm. If unit feels hot when it shuts off, it's a themal overload, put in to keep the reciever from getting damaged. It comes back on when cool right? Overload could be on its way out and shutting down at a lower temp too

Jan 05, 2010 | Yamaha RX-797 Receiver

2 Answers

Overload on screen


Check the speakers maybe one is already about to burn

Aug 21, 2009 | JVC RX-7010V Receiver

1 Answer

On screen says overload


yaa! my reciever does that too!! whats the problem?

Mar 16, 2008 | JVC RX-5030/32 Receiver

1 Answer

Jvc receiver OVERLOAD


possible short across speaker wires somewhere or even inside speaker

Dec 21, 2007 | JVC RX-6000V Receiver

1 Answer

JVC RX6040 OVERLOAD TROUBLE


clean your volume control if that does not help take it to a tech for repairs.

Mar 29, 2007 | JVC RX-6040 Receiver

1 Answer

OVERLOAD


I had incountered before VICTOR colored TV.ive found out that the problem was in the switch relay on the power supply area.. My suggestion is to check the relays wich is located at the supply board area resoldered the pin to make sure the pin is in solid contact. or put an AVR back up to your TV. If the problem still occur check the regulator IC or try to change a new IC this might help the problem.

Feb 04, 2007 | JVC (TC30EHGDU6) VHS-C Tape (6-Pack)

Not finding what you are looking for?
Onkyo HTR500 Receiver Logo

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio Players & Recorders Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

 Grubhead
Grubhead

Level 3 Expert

5484 Answers

The Knight
The Knight

Level 3 Expert

75571 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...