Question about Ryobi Multi-Volt Battery Charger

2 Answers

Can a bad ryobi 18 drill ruin a new 18volt ryobi battery

When I tried a new 18 volt battery in an 18 volt drill that had over heated and would not work, the new battery went dead and now will not hold a charge. The fully charged battery went dead in 1-2 seconds, and now will not hold a charge. Thnaks Tiff

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 55 Answers

The drill sounds like it is done for. The battery may have a blown internal fuse or possibly the electronics circuit board got damaged.

Posted on Jan 16, 2015

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 74 Answers

If the drill has a short in it, then yes, it could short the battery out. Probably in the trigger switch.

Posted on Feb 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Black & Decker Cordless Hand Vac battery is dead and won't take charge, what do I do?


well obviously the battery needs replaced , now if it snaps on that makes it easy , but if its internal then its bit more trouble but not impossible , and you'll need to do a bit of research to see about costs of doing this vs' replacement of entire device, id start by looking up vac cleaner repair in your area , im sure they are a wealth of knowledge on this subject

Jan 12, 2017 | Decker Drills

1 Answer

Black & Decker Cordless Hand Vac Battery is dead


Go on eBay and either find the OEM battery pack or build one from separate cell which are also on eBay.

Jan 12, 2017 | Decker Drills

2 Answers

Can I take a new Bosch cordless drill with rechargeable lithium 27Wh battery on an Air New Zealand plane from Brisbane to Auckland. All in new case and separate from each other


batteries are not allowed on aircraft
However there are ways of taking it on an aircraft if you contact the airline office and follow the procedure laid down by regulations

Jan 09, 2017 | Bosch Drills

1 Answer

Need a wiring diagram for home-light drill ide-500re.to check why it will not start


if it is a forward / reverse drill check that the direction lever is fully either way
a bit off and it will not run

Jan 08, 2017 | Drills

1 Answer

I have a Hamilton sensitive drill press from Oak Ridge national labs auction that I am restoring to original. The riser post is stuck , I have tried penetrating oil heat gun, hammer and wood block, and...


this is the wrong section to post i think but do you have or know of a product call "CILLIT BANG",its sold in england under that name , if you can get some and soak the riser post for 24 hrs then i would think it should move , get the LIMESCALE and GRIME version good luck

Oct 07, 2014 | Drills

1 Answer

WHY DOES MY KAWASAKI 19.2 DRILL BATTERY WANT STAY CHARGED IT HAS NOT BEEN USED ABOUT 5 HR N 2 YEARS IHVE ALLWAYS HAD 2 CHARGER IT EVERY TIME I USE IT IT WANT STAY CHARGED LONG


Hello friend,
These sort of batteries need to be charged discharged quite often. ALWAYS read the manufacturers advice when you get a new one. If you dont charge it properly first time then it will NEVER work at full capacity.and will not last a long time
It appears your battery is now finished and will not hold its charge for long. All you can do is replace it ...sorry.

Aug 25, 2014 | Drills

1 Answer

How do I use a Vermont American #17192 Drill Press Stand? Anyone have an instruction sheet for this? I acquired one from a sale but am unable to figure out how to mount our drill onto it. Thanks.


I have one of these. 2c7c66c8-687d-4eff-b1b9-7685d2c6ebab.gif
Here you will see how the drill is mounted in the device. Position (b) around the handle and tighten it up untill drill seats firmly in place. Take a speed square, or normal square and eyeball or measure the drill to see if its straight. Use the alignment adjustment (A) to fine tune the drill to get the drill bit straight and square. Tighten up all the nuts holding drill in device and recheck the drill bit for straightness.. Put your work under the drill, press the trigger and lock into place to get the drill to constantly run without finger on trigger, pull down the press lever to drill your hole... Hope this helps!

Nov 02, 2010 | Drills

Not finding what you are looking for?
Ryobi Multi-Volt Battery Charger Logo

Related Topics:

499 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ryobi Drills Experts

JOHN LAPIER

Level 3 Expert

2396 Answers

Cindy Wells

Level 3 Expert

4856 Answers

yadayada
yadayada

Level 3 Expert

66452 Answers

Are you a Ryobi Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...