Question about Panasonic KXTPA50 Phone

1 Answer

Need to reset handset - Panasonic KXTPA50 Phone

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 2 Answers

IP Reset
IP Reset returns the basic network settings to their factory defaults. You can perform this operation from the
base unit or one of the handsets.
The following settings will be reset to their factory defaults:
DHCP setting (restored to DHCP on
• Settings related to static IP addressing (the values for static IP address, subnet mask, default gateway,
DNS1, and DNS2 are cleared)
• DNS settings for DHCP connection cleared


1.2 Reset and Firmware Update
1.2.1 Reset
1.2.1.1 Resetting the Network Settings IP Reset
Performing IP Reset from the phone user interface see 2.1.4 IP Reset restores the basic network settings
made through phone user interface programming or Web user interface programming to their factory defaults.
If the unit is unable to connect to the network after changing network settings, you can restore the network
settings to their factory defaults by performing IP Reset, and then try configuring the settings again. Settings
such as the phonebook data, are not cleared by this feature.
The following settings will be reset to their factory defaults:
• DHCP setting restored to DHCP on
• Settings related to static IP addressing (the values for static IP address, subnet mask, default gateway,
DNS1, and DNS2 are cleared)
• DNS settings for DHCP connection (cleared)
• PHY settings (speed and duplex mode of the either LAN or PC port are restored to "automatic")
• VLAN (Virtual Local Area Network) settings (disabled)
• Terminal number settings (restored to "automatic")
Notice

After performing IP Reset, the unit will restart automatically. To avoid problems, it is recommended that
you save your settings before performing IP Reset.
Note

If these settings (with the exception of PHY settings and terminal number settings) were made through
Web user interface programming, the set values made through Web user interface programming
remain effective, even if you perform IP Reset. To reset these settings to their factory defaults, perform
Reset Web Settings from the Web user interface again.
Document Version
2010-08
Administrator Guide
www.InternetVoipPhone.co.uk ' sales@internetvoipphone.co.uk ' 0800 088 4846
Firmware Update

If these settings (with the exception of PHY settings and terminal number settings) were made through
configuration file programming, the set values made through configuration file programming remain
effective, even if you perform Reset Web Settings.
Resetting the Settings Made through the Web User Interface
(Reset Web Settings)
Performing Reset Web Settings from the Web user interface see Reset to Defaults) resets the
settings made through the Web user interface to their default values.
When you use this feature, the unit will return to the status just after performing the most recent provisioning
or pre-provisioning.
Notice

After performing Reset Web Settings, the base unit will restart automatically. To avoid problems, it is
recommended that you save your settings before performing Reset Web Settings.
Note

The settings configured through the phone user interface only will not be reset. However, settings that
can be configured through both the phone user interface and Web user interface will be reset.
1.2.2 Firmware Update
You can update the unit's firmware to improve the unit's operation. You can configure the unit so that it
automatically downloads the new firmware file from a specified location. The firmware update will be executed
when the unit is restarted.
For details, see Section 6 Firmware Update.
Provisioning server
Firmware server
Configuration
file
A
Firmware
C
B
A Download
B Check for update
C Firmware download and update
34
Administrator Guide
Docume

Posted on Jan 16, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Panasonic KX-TG5571 Base Unit. I have gotten rid of a handset and need to deregister it from the base, but the handset is required to deregister it.


  1. You need to know what the extension number was (1 - 8), look at the others to figure out what one is missing (the one you don't want anymore).
  2. On the base unit, press and hold [INTERCOM] until the CHARGE indicator flashes.
  3. Then, press and hold the handset's extension number (1 - 8) that you do not want for 5 seconds. A long confirmation beep should sound.

Feb 06, 2016 | Panasonic Lands Phones

2 Answers

My phone keeps rebooting


I faced the samed problem.A lot of minor issues regarding the handset could be solved through restoring of the factory settings. Go to Settings-privacy-Factory data reset, select "Reset Phone" and click the pop-up icon "Erase everything". The reset process takes about one minute and after that the handset will be restarted and stop on an English interface. Pull out the battery directly and reinstall it to turn on the handset.You need to backup the data before you reset the phone.

Feb 24, 2013 | ZTE Score

2 Answers

Need to reregister att tl86009 with new base


The secret decoder key sequence, provided by AT&T tech support, to factory reset this handset is:

(right softkey "-") * 3 3 1 7 3 4 # (left softkey "-")

The handset they should beep and go into registration mode.

Oct 04, 2012 | AT&T ATT TL86009 Phone

2 Answers

E4 - Erros My uniden phone model TRU 9485 - 4WX after outage power, now on LCD screen appear E4 and it didn't respond to any button when i press. I read some help which they say press 3 button...


Hello
Connect the phone line and power UP the base unit. Place the handset on base to get charged. It must reset automatically when you place the handset on base to charge. If not; resetting both handset and base unit is necessary.
Resetting the Handset

You may need to reset your handset in the following instances:

You lose a handset and purchase a new one. When you try and register to your existing base you get registration

failure.

You are unable to register any handsets to the base.

You had a base which needed to be exchanged by the manufacturer. When you register your existing handsets

to the base, the handsets say #3 and #4, but you only have 2 handsets.

When you are instructed to by the one of the manufacturer's call center representatives.

To reset, do the following:

Press and hold [ ] and [#] for more than 5 seconds. Select DEREGISTER HS.

WHICH HANDSET? appears. Select the handset that you want to de-register, and press the OK soft key.

DEREGISTER HS appears. Select YES, and press the OK soft key.

ARE YOU SURE? appears. Select YES, and press the OK soft key. You will hear a confirmation tone. The

handset will clear its registration information from the base, and then delete its own base information.

MODELS VARY! PLACE HANDSET ON THE BASE FOR REGISTRATION OR REFER TO OWNER'S MANUAL. To

re-register the handset to the base (see page 25).

If the handset cannot contact the base, it will display OUT OF RANGE. Make sure the handset is in range of the

base and the base is connected to power.

Note: It is also possible to reset the handset back to its original factory settings. All changes including Caller ID information

will be erased. For more information on resetting the handset back to factory settings and when you need to

do this, see www.uniden.com or call our Customer Service Hotline. See back cover page for contact information.

Resetting the Handset without the Base

If your original base is not available for some reason (for example, it is lost or somehow incapacitated), you can still

reset the handset and use it with another base.

Press and hold [ ] and [#] for more than 5 seconds.

Move the cursor to select BASE UNAVAILABLE and then press the OK soft key.

BASE UNAVAILABLE appears.

Move the cursor to select YES, and then press the OK soft key. ARE YOU SURE?

appears.

Move the cursor to select YES, and then press the OK soft key. You will hear a confirmation tone. The handset

will delete its own base information without trying to contact the base. When the base information is deleted,

the handset displays MODELS VARY! PLACE HANDSET ON THE BASE FOR REGISTRATION OR REFER
TO OWNER'S MANUAL. Register the handset to the new base (see page 25). of its user manaul.
OK.


Sep 12, 2011 | Uniden TRU9485 Cordless Phone

1 Answer

My sister forgot the password to her phone


im sorry about that! the problem is all your info will be lost. you need to enter the following steps which will reset your code, but will also reset your phone and information. i found this at t-mobile.com/forums.

A phone lock or security code on most Samsung handsets can be overridden by performing a full reset on the device. This will set the security codes on the handset back to the default eight zero's (00000000).


Important: This reset restores the original factory settings and will erase all downloaded content, including ringtones, images, programs, and contacts stored in the internal memory. It does not erase data stored on the SIM card or memory card (if available). Make sure you have backed up contacts, calendar appointments, and other data before continuing.


1. Power off the handset

2. Remove the battery

3. Remove the SIM card

4. Reinsert battery ONLY

5. Turn handset on

6. At the Insert SIM prompt screen enter the following code: *2767*2878#

NOTE: If using a handset that was released after July 2009 use this code: *2767*3855#

7. The handset should display E2P custom reset

8. Power off handset

9. Reinsert SIM card

10. Power on handset

11. The phone should be unlocked

NOTE: If you didn't get a E2P custom reset or a Full reset message on the handset your Samsung model may need an MCK code. You will have to call technical support for this code. Please have your IMEI number ready to expedite the process for this code. Your IMEI number is located on a label on the back of the phone,under the battery.

Dec 24, 2010 | Samsung UpStage SPH-m620 Cellular Phone

1 Answer

Master reset codes for Motorola MD61 handsets


Remove the spare battery (if any) and handsets from the base station.
Navigate in the menus to the "base settings". Your screen should say "ringer volume, ringer melody, keypad tone, tone/pulse, ..."
Punch in the reset code (including the stars): **335782
Wait for the phone to restart itself (about 5 seconds).
Re-register all of your handsets.

Dec 15, 2009 | Motorola Mobility MD681 5.8GHz Digital...

1 Answer

Uniden TCX905 cCordess phone Handsets # 3 and 4


If the handsets are not currently registered to any base, the SYSTEM RESET menu won't appear.

If the TCX905 handsets in question are actually expansion handsets from another Uniden Phone System, they are not true TCX905 handsets. To verify, remove the battery cover and battery, then look at the inside label. If it lists the model of a TRU9xxx phone system, your handsets are NOT TCX905.

Uniden unfortunately has programmed the expansion handsets from SINGLE LINE TRU9xxx phone systems to NOT REGISTER against the TRU9466. (Those same handsets register fine against predecessor model TRU8866 though).

Jun 14, 2009 | Uniden 5.8GHz Dual Cordless Phone

1 Answer

Gigaset 8800 PIN reset


  1. Turn the handset off by pressing and holding the PWR key.
  2. While holding down the keys 1, 4, and 7, turn the handset back on.
  3. It will display "Handset Service".
  4. While this message is displayed, type in the numbers 4 6 8 5 4 6 3 (the word "hotline") on the number pad.
  5. The phrase "Settings Reset to Default" for a second or two and the handset will power itself off.
Note: When you turn the handset back on, the handset PIN will be reset to 0000.

Dec 26, 2008 | Siemens Gigaset 8800 Cordless Expansion...

2 Answers

Searching is displayed on handset and Y icon is blinking, looks like a twig sign, have tried move closer to base station, base station is on reset unit restart handset reg, have tried all but gets to...


Turn base around and find the area which says pager/registration. Push this button after you set internally the handset registration.
Menu/H set settings/Reg. Handset

Dec 03, 2008 | Lands Phones

1 Answer

Handset Fails to Register


It is quite possible that you'll need to go into the menu settings on your base-unit and reset the unit or restore factory default, whichever option it gives you. Also, look in the menu on the phone to see if there is an option to reset the handset also. After resetting the unit and/or handsets, try to register the handsets again, one at a time. If that still does not fix the problem, you may have handsets that are not compatible with your system, or your system may not be able to support that many phones. However, if you have the right handsets, and your system can host that many handsets, then I'm confident that resetting the unit and re-registering your handsets should fix your problem.
Hope this helps! Have a nice day!

Apr 05, 2008 | Uniden DCX640 Cordless Expansion Handset...

Not finding what you are looking for?
Panasonic KXTPA50 Phone Logo

2,893 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Lands Phones Experts

kakima

Level 3 Expert

102366 Answers

john milligan

Level 3 Expert

512 Answers

george  peters
george peters

Level 3 Expert

860 Answers

Are you a Panasonic Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...