Question about Yamaha RX-V1200 Receiver

1 Answer

Yamaha RA-V1200 wont turn on - Yamaha RX-V1200 Receiver

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Check ur speaker wires, try disconnect all wires from back of unit and then try to turn on unit .if it stays on whit no wires attached than u have short connection at speaker wires . if doesn`t come on then try to fasten screws at back of the unit , may sound like BS but if amp board don`t have good ground connection it can go in protection mode
happened to me on RX-V592

Posted on Jan 29, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Yamaha dt230 wont start ?


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
dt 230 Dies
Steps to Take When Your Motorcycle Won Start Dennis Kirk Powersports Blog
Yamaha DT230 4TP3 AE1 Service Manual
OEM parts for Yamaha
Yamaha DT230 Owner Manual

Dec 04, 2012 | Yamaha Motorcycles

1 Answer

I have a Yamaha RX-V1200 receiver (6.1).


I would get it assessed to see if the unit is worth repairing. There are Ic's and stand alone transistors that could add up when it comes to repairs.

Mar 28, 2012 | Yamaha RX-V1200 Receiver

1 Answer

Lost my power cord for my receiver, where can i get a new one


Hello
This is the picture of the power cord you have to buy. It can be bought either form the authorised service ceter for Yamaha or from any local electronic sparepart selling shops at your town. OK.


11_30_2011_2_37_45_am.jpg

Nov 30, 2011 | Yamaha RX-V1200 Receiver

1 Answer

TEAC AG-V1200 receiver won't auto turn on when


No. It won't automatically turn on when power is present.

Aug 08, 2011 | Teac Audio Players & Recorders

1 Answer

AV receiver RX-v1200


What happens when you turn it back on?? Are there any messages on the display??

Jul 03, 2008 | Yamaha RX-V1200 Receiver

1 Answer

Yamaha rx-v1200 volume control


if you are not really that technical type that can make repairs then it will be very hard for you to replace it yourself. not hard to find the volume control, it is mounted on a board. you dismantle the board first then remove desolder the volume control. it think you can onyl get the parts from yamaha service.

May 05, 2008 | Yamaha RX-V1200 Receiver

1 Answer

Volume knob quirks


if you know how to repair, then replace the volume control switch. it is a digital type/mechanical type of switch with silicone oil on it to prevent sudden turn of volume. if i were the repairman i can simply clean the contacts of the volume control and pour silicon oil again. but i really dont know in your area if they try to clean those.

May 03, 2008 | Yamaha RX-V1200 Receiver

1 Answer

Yamaha RX-V1200 subwoofer connection to Mirage BPS-150i subwoofer


just connect your subwoofer mono RCA to your amp sub single out rca connector. you do not need to megre all those 4terminals into one. in fact internal circuit of those 4rca are merging inside to one since the sub uses only a single amp. 4inputs was meant for sources with multiple sub out

Nov 02, 2007 | Yamaha RX-V1200 Receiver

1 Answer

RXV1200 A/V receiver


please check your speaker cabling first for possible short connections. if all ok, then remove the speakers (all) and try to turn on the unit. If still doing the same thing then you have busted one of your amplifier. it can be any of the amplifiers (main center surround etc...

Aug 18, 2007 | Yamaha RX-V1200 Receiver

Not finding what you are looking for?
Yamaha RX-V1200 Receiver Logo

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5047 Answers

The Knight
The Knight

Level 3 Expert

74106 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Yamaha Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...