Question about Hoisting

1 Answer

What maintenance is necessary for my wire hoist?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 75 Answers

I would recommend lubricating the entire system every couple months. Also OSHA has to inspect it every year

Posted on Jan 16, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the wire ( which has broken ) when you peg your clothes on the clothes line ?


hills used wire available from bunnings hardware or any hardware shop

May 18, 2016 | Cars & Trucks

1 Answer

How to remove engine


Hire engine hoist, remove radiater, exhaust, cabled engine secure bolts on rubbers, remove bolts on clutch to engine, on hoist slowly move engine towards front and lift out of engine bay.

Aug 13, 2014 | 2008 Taurus X Engine/Motor g66117850l...

1 Answer

Are wire hoists as strong as chain hoists?


Wire hoists are as strong and in some cases can be stronger even than chain hoists being able to lift between 1/2 up to 80 tons.

Nov 21, 2013 | Hoisting

1 Answer

What is OSHA and why do they need to inspect my wire hoist every year?


OSHA is the United states department of labor Occupational safety and health administration. They have to inspect your wire hoist every year to make sure that you and your employees are safe when they are using the wire hoists in your facility.

Nov 21, 2013 | Hoisting

1 Answer

Where can I find instruction for installing a wire hoist?


I found this set of instructions to be very detailed and helpful when I had to set up my wire hoist. Good luck and stay safe!
http://voices.yahoo.com/how-install-wire-rope-hoist-7673214.html?cat=6

Nov 21, 2013 | Hoisting

1 Answer

What are the advantages of a wire hoist over a chain hoist?


chain hoists are heavier, and are more susceptible to rust, although wire hoists can also rust

Jan 16, 2013 | Hoisting

1 Answer

I am looking for a diagram of the bumper assembly for a 2004 Chrysler town & country.


Hope this helps, it it does please leave feedback and vote Thank You and Good Luck


  1. Release hood latch and open hood.
  2. Remove the headlamp assemblies.
  3. Hoist vehicle and support with safety stands.
  4. Remove the five push pin fasteners attaching bottom of fascia/air dam to radiator closure panel.
  5. Remove front wheels.
  6. Remove front wheelhouse splash shields fasteners as necessary to gain access to bolts attaching front fascia to fender.
Fig. 1 133387737
Fig. 2 133387738

  1. Remove the two bolts and two nuts attaching fascia to the front fenders (Fig. 1) and (Fig. 2).
  2. Disconnect fog lamp wire connectors, if necessary.
  3. Lower vehicle.
  4. Remove two bolts attaching the upper grille support to the headlamp mounting panel at each side of the grille.
  5. Remove bumper fascia from vehicle.
INSTALLATION


  1. Position front bumper fascia on vehicle (Fig. 1) and (Fig. 2).
  2. Install the two bolts attaching fascia to headlamp mounting panel at each side of grille.
  3. Hoist vehicle and support with safety stands.
  4. Install the two bolts and two nuts attaching fascia to the front fenders. The fascia should be flush to fender.
  5. Install front wheelhouse splash shields fasteners.
  6. Install front wheels.
  7. Connect fog lamp wire connectors, if necessary.
  8. Install the five push pin fasteners attaching bottom of fascia to radiator closure panel.
  9. Lower the vehicle.
  10. Install the headlamp assemblies.

Jan 02, 2011 | Chrysler Town & Country Cars & Trucks

1 Answer

The cable for the spare tire on my 2006 1500 works fine (it's all the way down) but the retainer did not lower at all so I cannot pick up the spare tire. Can anyone help? Thanks


  1. Rotate the hoist shaft counterclockwise until approximately 15 cm (6 in) of cable (1) is exposed.
  2. While holding the latch pin (3), fully depress the latch button (2) and release the secondary latch from the hoist assembly. Some side-to-side and/or up-and-down movement may be necessary to disengage the latch mechanism.
  3. Continue rotating the hoist shaft counterclockwise in order to lower the hoist the rest of the way.
  4. If this does not release the secondary latch, the spare tire hoist will need to be replaced. See the following procedure.
Important: If the spare tire hoist has been fully raised without a spare tire in place, the secondary latch mechanism may have become engaged. If this has occurred the hoist will not lower and the following steps will need to be followed:

Nov 01, 2009 | 2005 Chevrolet Silverado

1 Answer

Havin troubles removing the rear hub on a F150




  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer Maintenance/Service and Repair.
  2. CAUTION: Do not allow the caliper and anchor plate assembly to hang from the brake hose or damage to the hose can occur. Remove the bolts and position the caliper and anchor plate assembly aside.
    • Support the caliper and anchor plate assembly using mechanic's wire.
    • To install, tighten to 200 Nm (148 ft. lbs.) .
  1. Remove the brake disc.
  2. Remove and discard the wheel hub nut.
    • To install, tighten to 400 Nm (296 ft. lbs.) .
  1. Remove the wheel bearing and wheel hub assembly.
  2. If necessary, remove the wheel bearing from the wheel hub.
  3. CAUTION: Do not apply lubricant to the threaded end of the wheel spindle. NOTE: Clean the wheel spindle (including the threaded end) of any dirt or grease using the specified solvent before installing the brake disc. To install, reverse the removal procedure.
    • To ease installation, lubricate the inner race of the bearing assembly using the specified lubricant.

Oct 31, 2009 | 2006 Ford F-150

1 Answer

How to wire


use a wireless controller it will be cheaper and easer http://www.telecrane.com/

the three wires are

x1 constant power
up
down

x1 is connected to the up or down wire to activate the hoist in the desired direction

Mar 16, 2009 | Jet Equipment Chain Hoist 1TON 10 Ft Lift...

Not finding what you are looking for?
Hoisting Logo

Related Topics:

1,087 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoisting Experts

Jerry Kramer
Jerry Kramer

Level 3 Expert

3904 Answers

FIREFOX ENGINEERING

Level 2 Expert

325 Answers

Brad Brown

Level 3 Expert

15478 Answers

Are you a Hoisting Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...