Question about Zanussi WJS1265W Front Load Washer/Dryer

1 Answer

Mid wash I am gettign E10 messages

In the middle of a wash I get an E10 error with beeper sounding.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 373 Answers

The manual suggests the following for E10 error --- 'The Water tap is not turned on.'
It is a valve fault.It is not taking the water in possibly. It is the green side of the triple valve. Try manual clearing the valve.Else The water inlet valve might need a replacement.
Good luck with the machine.Please do rate my solution.Also do post comments for further help if needed.

Posted on Jan 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My ultima1000, wm 71 says error 10 sometimes and error 11 mid way thru a cycle. The pipes are fine and water is on what could be the problem?


E10 No cold fill detected - washing machine does not fill
  • Check mains water pressure
  • Check inlet hoses for kinks
  • Check inlet filter
  • Check water inlet valve
  • Pressure switch fault
  • Wiring fault
E11 Not hot fill detected - washing machine does not fill
  • Check mains water pressure
  • Check inlet hoses for kinks
  • Check inlet filter
  • Check water inlet valve
  • Pressure switch fault
  • Wiring fault

Apr 11, 2016 | Washing Machines

1 Answer

Why does it stop in mid-cycle and display error E10?


Error codes are model specific water is your model number?

Feb 05, 2016 | Washing Machines

1 Answer

Washing machine beeps, doesn't run


1 Beep/E10--Error: Water doesn't enter Cause: Water supply problem, Check kinks and faucets
1 Beep/E10--Error: Water leaks Cause: Water connections loose,household drain clog,oversudsing. Correct problems.
1 Beep/E10--Error: Dispenser drawer is open Cause: Washer will not operate if drawer is open.

Jan 08, 2014 | Kenmore HE2 Plus Front Load Washer

1 Answer

Electrolux ewf1083 stops mid cycle displays e10 .press start button and continues but can happen up to 4 times per wash.any ideas?


We had the E10 error on EWF1083, I opened the top cover and looked into it. It's the 2 way solenoid valve and should be a easy replacement. Looked on ebay and $59 for the part ex postage

Oct 12, 2011 | Washing Machines

1 Answer

I have an frigidaire front load Mod.# GLTF2940ESO with an recurring E10 error message. HELP!!


E10 code indicates there is no water supply.This can be confirmed by :
  1. Shut off the faucet to stop water supply to the washer.
  2. Disconnect and pulling the supply hose off the washer to confirm the E10Code
    • Opening the faucet and watch for running water



E10 also means that your cold water is coming in too slow, disconnect the cold water hose and check to see if the screen on your washing machine is clogged. If the screen is clean and the hose has good pressure then you will need to replace the water valve on your machine--- this is the piece that the hoses directly connect to.

Apr 11, 2010 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

I have a Fridgidaire Front Loader Washer _ Affinity. It has an error message flashing. E10. What does that mean? What do I do to fix it?


I have a Fridgidaire Front Loader Washer _ Affinity that flashed the E10 error code. I also had the problem with the fabric softener dispenser not emptying, and staying full of water. The problem was the cold water filter on the back of the washing machine that was semi-plugged. Cleaned the filter and now works perfectly. My machine is no longer flashing the Error code 10. The dispenser works perfectly.

Oct 05, 2008 | Frigidaire Affinity ATF7000ES Front Load...

1 Answer

E10 error message


I have had the same problem on an AEG. The problem it refers to is that there is not enough water entering the machine. Either the water pressure is too low or there is something blocking pipes/filters. Hope this helps

Apr 23, 2008 | Zanussi ZWF1430W Front Load Washer

1 Answer

Error E90


That happened to mine, and apparently it is the connection to the control panal at the front of the machine or the desplay unit (4 blue wires). Take the top off and wiggle them around or re-connect if any are loose. Mine worked for one wash and then started displaying E10........so i'm not amused and I think i may end up getting a hotpoint!

Nov 09, 2006 | Zanussi WJS1265W Front Load Washer/Dryer

Not finding what you are looking for?
Zanussi WJS1265W Front Load Washer/Dryer Logo

401 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...