Question about Xerox WorkCentre XD125F All-In-One Laser Printer

1 Answer

Shows l 6 on screen

What does that meen

Posted by on

  • patel1174 Jan 24, 2009

    i have xerox workcenter 125f on display it flash L and then 6 WHAT IS THAT MEAN

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,072 Answers

An L6 is related to the laser polygon motor. Either the laser unit is bad or the main processor. You can try and take the back cover off and resetting the connectors on the circuit board. But most likely it is the laser.
You can google "the parts drop" to find out prices on those.
It is a lot of work to replace a laser in that product.

Posted on Jan 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why brother printer do not work?


ask the question cleyar do not work meens it' not power on r that one showing any light simble must write

Aug 25, 2014 | Printers & Copiers

1 Answer

What causes a dirty background?


Copied
1) - Power ON printer while holding both the + & - buttons until "OKIUSER" message appears in LCD.
2) - Press + or - button until "ENGINE DIAG MODE" is displayed.
3) Press "ENTER", displayed will be "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or - button until "NV-RAM INITIAL" is displayed.
Half way, dont stop too long it will time out....
5) Press "ENTER" again.
6) Will appear "TABLE 1" message.
7) Press "ENTER" until "EXECUTING RESET" message appear. ...............the "NV-RAM INITIAL" message will BLINK.
Tada....This procedure reset TONER, DRUM, FUSER and BELT...life counts
8) power OFF printer, wait 10 sec, and power ON again..

To access Service Mode in C9300 power ON printer with 0, 1, 6, 7 at same time...you can do some good damage in there!! (I warned ya!)

Resetting consumables for OKI C7300,C7500,C9300 printer I think!

1. Hold buttons 0 + 1 + 6 + 7 on startup.

2. Press button 0 several times until "DIAGNOSTIC MODE xx.xx.xx" shows.

3. Hold buttons 2 + 3 until "ENGINE DIAG LEVEL 4" shows.

4. Press button 1 to scroll to "COUNTER SET".

5. Press button 2 to scroll through menu items (button 6 scrolls backwards)

6. To alter the value of an item, first press button 3 to select the digit to be altered. The selected digit will slowly flash. (Button 3 moves to the right through the digits. Button 7 takes you to the left.)

7. Then press button 2 to increase the value of the selected digit. Press button 6 to decrease the value.

8. When the changes have been made hold buttons 1 + 3 + 5. The screen will flash three times and then an * will appear on the right of the screen. The new value is set.

9. To leave the counter set menus, turn the printer off.
IMPORTANT

Each colour toner counter shows life as percentage used. So a toner showing 30% has used up 30% of its toner. 100% would indicate a near empty toner. This is the reverse of the toner life shown from the "usage menu" when the printer is in normal operation, which shows the toners as a percentage life remaining. You will want toner showing 00%. note:this is oposite of what you see in user mode
Some models exhange these steps

3) HOLD 0 + 4 "ENGINE DIAG LEVEL 2" shows

4) Press 1 to cycle to "fuser unit"

5) 2 to scroll to TONER

REST IS SAME WE WANT TO SET WHAT i GUESS IS AT 100% TO 0%.

Jun 10, 2014 | OKI C9600hdn Laser Printer

1 Answer

MFC-7840W Printer Brother, we have replaced the toner many times and the printer always shows the message on its screen: low toner, and after that shows: toner life end, what we can do, because this is the...


Open the front cover. Remove the drum and toner. Remove the toner from the drum by pressing and holding the green/blue tab on the right side then lift the toner out. Shake the toner side to side for 6 times, and on the drum unit slide the blue/green tab on the far left side from left to right for 6 times also. reinstall the toner back to the drum unit. reinstall drum and toner back to the machine. Close the front cover. The display should show the date and time.
Hope this will help.

Mar 25, 2011 | Brother MFC 7840W Printer

1 Answer

HAVE A BROTHER COPIER MODEL # 8045D WITH ERROR CODE OF "A 6" WHAT DOES THIS MEAN?


i don't know what A6 meens, but if u make a mistake and the error is 6A it mean that u have problemi n fixing section - heater lamp or the termistor are broken!

Aug 11, 2009 | Brother Printers & Copiers

1 Answer

Toshiba e-studio120, H4 error code. what it`s meen??


seems like heat roller problem.
enter code C, exposer light buttom, C and exposer light buttom , then all the indicator in the machine goes off. then enter 14 and press print buttom. Now your machine must work. If not Pls refer to technician.

Jul 08, 2009 | Toshiba e-Studio120 Copier

4 Answers

Printer


try printing a test page. Make sure you have the right driver for your printer. Make sure all connection are secure and tight.

Mar 27, 2008 | Compaq Inkjet IJ650 Printer

Not finding what you are looking for?
Xerox WorkCentre XD125F All-In-One Laser Printer Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Printers & Copiers Experts

Whit
Whit

Level 1 Expert

185 Answers

iteminconline

Level 2 Expert

110 Answers

Philip Hughes

Level 2 Expert

63 Answers

Are you a Xerox Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...