Question about Precor Exercise & Fitness

Open Question

Remove the shroud from the 9.10 treadmill

How to remove the shroud

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove fly wheel?


Before you try removing flywheel look for wear on the outside shrouds covering the fly wheel area and adjust if need be. If you need to remove flywheel you have to remove the arms first before taking off flywheel shrouds to exspose inners this project will take you some time

Jun 24, 2014 | Golds Gym StrideTrainer 595 Elliptical

Tip

95Xi Crosstrainer Shroud Replacement


Video Presentation of Replacing the Main Shroud on a LifeFitness 95Xi Crosstrainer


  • The video shows the steps involved in replacement of the main shroud on a LifeFitness 95Xi


  • Tools:



    • Phillips Screwdriver




  • Remove the (4) screws securing the main shroud to the drive frame assembly



    • There are two screws on each side




  • Lift straight up on the shroud to remove it


  • Install the main shroud in reverse order



    • Making sure the main shroud fits into the grooves of the lower shroud panels




Repair Video for LifeFitness 95Xi Crosstrainer Shroud Replacement

on Feb 11, 2015 | Life Fitness Crosstrainer, 9100, 9500 Rear...

1 Answer

How do you remove pedal arms on schwhinn biodyne 220 so the shroud can be removed?


There should be a circular insert at the shroud that the crank arms for the pedals go through. It took me a little careful work to pop the inserts out of the shroud. This leaves a just enough space to carefully squeeze the shroud over the pedals allowing access to the interior. Its a tight fit and may require tackling it from different angles to get the shroud off. It can be done, but be careful not to apply too much pressure resulting the cracking off the shroud.

May 26, 2014 | Schwinn 220 Recumbent Exercise Bike - 2012...

2 Answers

I bought my treadmill about a month ago and have used it a couple times but now I get no power. I plugged the treadmill into a power strip and then into the wall outlet.


Check if you are getting power to the treadmill by simply plugging in a lamp first to the outlet then the power strip then check if the on/off reset is engaged. Then if you have to proceed to under the motor shroud (See owners manual for removing shroud) you will need a multi-meter to trace back to the Motor Control Board to see if you are getting AC Power. You should be still under manufacturer,s warranty call them for service in that case.

Jun 13, 2010 | Proform 790T Treadmill

1 Answer

My daughter plugged the unit into a 220 outlet i think. But I cant get to the fuse. is there a trick to opening and getting to it so i change it??


By the power switch their is a circuit breaker reset it. These units do not have a fuse for the main line AC if that does not restore power to the treadmill you may have a problem with the lower electronics . On opening the motor shroud their should be a couple screws holding the shroud carefully rotate and lift shroud off.

Jun 12, 2010 | Nordic Track Nordictrack Apex 4100i...

1 Answer

Treadmill cuts out and says check sencor


Unplug unit remove the motor shroud depending on your manufacturer its either on the frame by the front roller/ pulley or is attached on to the driver motor. On the lower electronics when you turn on the treadmill you should see LED and is labeled speed crtl if you push the running belt with your foot that LED should flicker if does not then the speed sensor is bad.

May 13, 2010 | Exercise & Fitness

1 Answer

Where is the speed sensor connection located on the treadmill?


Unplug unit the remove motor shroud most sensors are next to front roller/pulley assembly it will be either a black rectangular or cylindrical (reed switch) component adhere to the frame or locate on either end of the drive motor.

May 14, 2010 | Bladez Ion 9.9 Fold-up Treadmill

1 Answer

How to remove hood no screws --nordic track commercial 1500 treadmill


The motor shroud has 3 Phillips screws under the front under belly that releases shroud you should be able feel them with finger tips.

Mar 16, 2010 | NordicTrack Exercise & Fitness

2 Answers

Thumping noise that increases with speed


OPEN MOTOR SHROUD SO YOU CAN BETTER INSPECT THE UNIT CHECK THE DRIVE BELT THEN I WOULD CHECK THE RUNNING BELT TO SEE IF THEIR IS ANY DEBRIS THAT THE BELT ITSELF IS SPLITTING SINCE YOUR SAY A THUMPING SOUND. SINCE KEYS FITNESS MADE THIS UNIT THEY ARE NO LONGER IN BUSINESS, BUT TREADMILL DOCTOR HAD PURCHASED THE PARTS. SO GO TO TREADMILL DOCTOR.COM THEY MAY HAVE THE PARTS YOU NEED

Mar 01, 2010 | Smoothfitness Smooth 5.45 Folding...

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Precor Exercise & Fitness Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Howard
Howard

Level 2 Expert

115 Answers

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

Are you a Precor Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...