Question about Tools & Hardware - Others

1 Answer

Where can i find plans for building a flip top tool stand?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Teacher:

    An expert who has written 2 tips or uploaded 1 video tip.

  • Expert
  • 152 Answers

Http://www.bt3central.com/showthread.php?t=39913

Posted on Jan 15, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the spokes on the rear wheel of a huffy 18 speed bicycle


you will need several specialized bike tools that will make this cost prohibitive for the DIYer unless you plan on doing more wheels. Most local bike shops can sell you a replacement wheel for between $35 and $50 and remove and reinstall the freewheel, rimstrip, tire and tube and reinflate it for about $8-10. Also the quality of this replacement wheel will be a much higher than the original Huffy wheel.



If you still want to do it yourself, you will need a freewheel removal tool for your specific brand of freewheel or cassette (there are about a dozen different types of tools out there, so make sure you get the right one). You will need a spoke wrench of the right size for the spoke nipples you are using, there are three common sizes and a couple more odd size ones out there. You are looking at about $20-$30 for those tools. You should use a truing stand to true the wheel after the spokes are replaced ($150-$400) but you can "get by" with using the brakes in your bike as a reference. Spokes will run you $1-$2 each. If you don't have a special metric spoke ruler ($10-$15), most LBS's will measure them for free (all bike parts are measured in metric). The details of lacing a wheel and getting the tension right is beyond the scope of this short answer and I recommend that you either try to find a book on the art of wheel building at your local library or buy one off of Amazon ($25-$45), there are several good ones out there and video tutorials also. If you plan on doing more than one wheel then I highly recommend it and take the time to learn the art, there are few of us left out there that can actually build a wheel these days.

Nov 18, 2015 | Huffy Cycling

Tip

With only two fairly clean adults in the house, I use the front loading Kenmore...


This advice is for preventing or getting rid off that awful mildew smell associated with front loader style washing machines.

The first thing to do is to CHECK IN AND AROUND THE RUBBER DOOR BOOT (called a bellow) for small articles of clothing (like socks and underwear) that may have gotten lodged in behind the rubber. Pull the rubber back where it meets the wash tub and look behind it. It is common for small items to get stuck here, become forgotten and start to mildew. You should check this area after each wash and clean it periodically to get rid of the formation of soap scum, mold, and mildew. HINT: When you get ready to wash a load of towels, take a dirty towel and clean the door boot thoroughly (including the areas behind the rubber). Immediately place the towel in the wash and run it on a sanitary cycle. This way you eliminate the need for cleaning rags.

PERIODICALLY RUN THE WASHER ON A CLEANING CYCLE. Place the washer on the hottest setting you have (usually a Sanitary cycle) with nothing but bleach in the wash tub. Some newer models actually have a “Clean Cycle” available now just for this purpose. This helps keep the wash tub, drain lines and pump sanitized.

CHECK AND CLEAN THE DRAIN PUMP FILTER. Accumulations of debris in the drain pump filter can also cause odors. HINT: If you own a shop vac, pull the drain hose from the standpipe at the wall and pull a vacuum on the line. This will drain any residual water left in the tub, pump and drain lines BEFORE you remove the drain pump cover. This will prevent a messy clean up later.

LEAVE THE DOOR OPEN IF POSSIBLE. When not in use, leave the door open to allow the tub to air out and to keep mold and mildew from forming on the door bellow. I know this may not be desirable in some households with small children. If too much mildew forms on the rubber and it cannot be removed, replacement of the bellow may be required.

NOTE: This problem is common with front loader style washing machines. The doors on these machines have an air tight/water tight seal that is great for sealing the washer during the wash cycle, but can be terrible for collecting small garments and for not allowing the tub to properly air out when not in use. Following these simple preventive measures can go a long way towards preventing harmful mold and mildew, and towards extending the life of the door bellow and pump.

on Apr 20, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Where can i buy a good flip top tool stand?


http://www.woodstore.net/flwoce.html


this is a great website for tool stands

Jan 15, 2013 | Tools & Hardware - Others

1 Answer

I need full construction plans on how to build a pizza oven out of brick


http://www.fornobravo.com/pompeii_oven/pompeii_oven.html
this site has alot of different options with plans available for you
good luck sounds like a cool project

Jan 23, 2011 | Master Bilt Pizza Prep Table 20 cu ft...

2 Answers

Measuring a Building


This is a pretty odd question, i think you don't need to measure it, you can check the building plans.

If you insist on measuring it I think your best option is a Laser Measuring Device, they are the easist to use.

Aug 28, 2008 | Dewalt Self-Leveling Line Laser...

Not finding what you are looking for?
Tools & Hardware - Others Logo

Related Topics:

791 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tools & Hardware - Others Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Brad Brown

Level 3 Expert

15441 Answers

Are you a Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...