Question about Office Equipment & Supplies

Open Question

My canon MX318 will not turn on. on button not working but checked that power is getting through needs a reset?

Tried to switch on but the on button doesn't respond I know power is getting through how can I reset the machine?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Mrvica
  • 167 Answers

SOURCE: Reset Waste Ink Canon MX318

Because It is full. And replace or you can clean it. Either way you must any of this two things.
Good luck.

Posted on Sep 16, 2008

tbirdfan1
  • 3051 Answers

SOURCE: Driver for Canon PIXMA MX318

you can go to radar sync.com and download their free driver utility it has worked well for me best of all it was free

Posted on Mar 21, 2009

  • 1 Answer

SOURCE: Reset Waste INk Canon MX318

help me please....!!
may printer error 5B00

Posted on Apr 01, 2009

  • 2 Answers

SOURCE: canon S 520 doesn`t print

Two flashes: Out of paper, paper jam or paper feed error
Replace the paper correctly and press the RESUME/CANCEL button.
If paper has jammed in the printer, clear the jam and press the RESUME/CANCEL
button.

Three flashes: Paper jam
If paper has jammed in the printer, clear the jam, replace the paper in the printer
correctly and press the RESUME/CANCEL button.

Four flashes: Empty ink tank
One of the ink tanks is empty. Replace it.

Six flashes: No print head installed
Install a print head.

Seven flashes: Defective print head
Remove and reinstall the print head.
Also, ensure that the protective tape has been removed. If reinstalling the print head
does not resolve the problem, replace it with a new one.

Eight flashes: Waste ink tank almost full
The printer has a built-in waste ink tank for the ink used during print head cleaning. Eight
flashes indicates that the waste ink tank is nearly full. Press the RESUME/CANCEL
button to cancel the error so you can continue printing. Before the waste ink tank
becomes completely full, contact a Canon service representative to have the waste ink
tank replaced. Canon recommends to call for service as soon as this error occurs. Once
the waste ink tank becomes completely full, printing will be no longer
possible.

Posted on Apr 03, 2009

  • 12 Answers

SOURCE: Trying to reset chip on refilled ink tank on CANON MP830

Looks like Fillserv.com has a chip resetter for the CLI8 color cartridges, but I don't know if that unit will reset the big black PGBK cartridge in the MP830.

Posted on Jun 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The problem mx318 Canon show check printer 5100. pls advime to slove the problem tq


my problem about chek printer 5800 canon mx318.
i dont no what can ido
please help me

Jan 06, 2011 | Office Equipment & Supplies

2 Answers

Cannon MX318 show alarm U162


Press and Hold the STOP/RESET button and wait until it self restart.
Release the STOP/RESET button when the printer is restarting

Aug 19, 2010 | Canon MX310 Office All-In-One Printer

1 Answer

Check ink U051 col


hi...you can try to press the reset button in five second.,.,

Feb 25, 2010 | Canon PIXMA MX310 All-In-One Printer

2 Answers

Erroru051


Canon MX300

Hi
It is ink low error U051

1. Disconnect the power cable
2. Connect it while holding down the power button
3. With the power button still down, press twice the "Cancel/Stop" red button
4. Release the power button
5. The prints turns into a kind of factory mode...(wait for about 10 seconds, utile it says "Idle")
6. Press the ">" (next to the "OK" button) once.” Shipping Mode 3"
7. Press the "OK" button.
8. Press "OK" again for "Without cleaning"
9. A test page will print.
10. Open the cover, like you are about to change the cartridges.
11. Disconnect the power cable again.
12. Take out both cartridges.
13. Close the cover.
14. Connect the power cable once again.
15. Turn the printer on.
16. Now just put the cartridges back...

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Feb 07, 2010 | Canon MX300 Office All-In-One Printer

3 Answers

Pixma mx328 check ink u051


The error usually came out after you refill ink on the black cartridge...there is no way you can make the printer work without resetting the ink cartridge..

Try to reset the printer using this procedure.. it will help.
1. turn off the printer..
2. press/hold the stop/reset button..and press/hold power button too..
3 while holding power button, release the stop/reset button..
4. then press the stop/reset button twice..
5. release power button..and wait until the power button lights a steady/still green and says "idle"...
6. open the cover...take out both catridges.. then turn off the printer.
7.put back the cover then turn on...
8. now put the catridges back.. and wait for some time to return to display menu... then try to print...

The printer may still prompt a "black ink volume unknown and color ink volume unknown" but don't worry that won't affect the operation of the printer. And you will able to use your printer, fax and scanner.

Do this every time you refill the ink of the cartridges.

If you find this solution helpful please vote on this on the YES below..thanks..

Dec 17, 2009 | Canon PIXMA MX310 All-In-One Printer

2 Answers

MX318 fails all fax functions


If you are using only one incoming telephone line, you need tro reset your printer at 'fax priority' position onn your printer. An MX-typr handicap.

Sep 20, 2009 | Canon PIXMA MX310 All-In-One Printer

2 Answers

Pixma mx318 paper jam


The first thing I would do is check if there is any small fragments of paper in the printer. If you still cannot see anything, try getting some compressed air and blown the printer out. If that still dose not fix it, you might have a faulty paper sensor. If the printer is in warrenty, I would try and do a warrenty claim.

Aug 29, 2009 | Canon PIXMA MX310 All-In-One Printer

1 Answer

Reset Waste Ink Canon MX318


Because It is full. And replace or you can clean it. Either way you must any of this two things.
Good luck.

Sep 16, 2008 | Canon MX310 Office All-In-One Printer

3 Answers

In March 2008, I bought a CANON printer "PIXMA MP210" series. But, only last week I was abled to errected and connected the printer to my Fujitsu Life Book # A6110 (lap top). When switching on the...


is there any error message appear at your laptop..? have you check the ink cartridge inside, and also the mechanical parts inside if there was a paper jam..

Jun 27, 2008 | Office Equipment & Supplies

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

k24674

Level 3 Expert

7993 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...