Question about Swann Communications Opti-Viewcam Webcam

Open Question

Question: Whats the default IP address of Swann MAX-IP camera...

Kindly email me the default IP... my freind lost the user guide. Pls help me. i search over the internet and no manuals & guide available

thank you very much

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I do i get the default username and password for vivotek fd8134 camera


An IP camera is a video camera that can be viewed over a Local Area Network or the Internet. The camera typically is monitored locally from a computer via the network to which the camera is attached. With just a few additional configurations of your network, you can access the IP Network Camera so that it can be monitored remotely using the Internet. This is the benefit of a network camera, as it can reside on an IP network and the video stream can be accessed or saved remotely.

Get the Default Gateway of your IP. step 2 Do this by entering "ipconfig/all" in your Command Prompt and hitting "Enter" on your keyboard. Your IP information will be brought up, and number you are looking for is the Default Gateway. This is underneath the IP address. Identify this number by its number pattern, which will look like the following: 111.222.3.4. Access your router. This is done by simply typing the default gateway from Step 1 above into the address bar of your Internet browser, and pressing "Enter." Forward your port by configuring your camera. Open the configuration section on the router web page where port forwarding is located by clicking on the "Applications & Gaming" link along the top of the page. In this menu, click on "Port Range Forwarding." Configuration sections can be located differently with each kind of router. Find this information by referring to the documentation that came with your router when you purchased it. Access your camera over the Internet. To do this, type your public IP address into the address bar of the web browser and press "Enter" in the same way as described in Step 2 when entering your default gateway. Note: The public IP address is different from your regular IP address. The regular IP address identifies computers and other devices on your network, whereas your public IP address is what is used to make yours lf known to others on the Internet. Your Internet service provider can supply you with your public IP address if you call them and ask for it. Hope it helps.

Jan 23, 2013 | Vivotek FD8134 - Network camera - dome -...

1 Answer

What is password default Cam IP 7134


The default root password is the 12 digit (upper case) MAC address, for example, 0002D 100337A . The user name is root. Try to use the MAC address to log in to the camera. Notice the capital letter.

Apr 12, 2011 | Vivotek PZ6112 Network Camera

1 Answer

How to connect to remote camera


To create new Camera Window
  • Click New Camera from the File menu.
  • Camera Setting dialog box appears.
Camera Setting dialog box

Camera Setting dialog box helps you control selected video source. To open the Camera Settings dialog box, select Camera Settings from the File menu.

Set a preview rate in the Preview Frame Rate box. It indicates the number of frames per second in the camera window. The default value is 10 frames per second. This value doesn't interfere with broadcast or record frame rate.


Remote Cameras
Remote camera is another Active WebCam program with enabled Remote Access launched on remote computer. Both programs use UDP protocol to communicate each other. If connection with Remote camera goes through firewall, make sure that the IP address of your computer, local and remote ports are opened on the firewall, and the UDP protocol is enabled.

To connect to Remote Camera
In the Device tab click to select Remote Camera.

Specify the computer address in the IP address box. Don't place the protocol prefix (like http://) in the address, just four digits of IP address delimited by dots, like: 192.168.1.101. You can find out the remote computer IP address by clicking Get Computer IP Address from the Tools menu on the remote computer.

Type port, which is opened on remote computer for remote access in the Remote Port box. This value is specified in the Port box in the Broadcasting | Remote Access properties on the remote computer.

Specify port, which will be used to receive data from remote camera, in the Local Port box. If your network uses firewall, make sure that Local Port and computer's IP address are opened in the firewall. Use the Check the Port Availability button to make sure that this port is not used by another program.

If the remote computer requires authorization, enter user name and password in the appropriate boxes. The authorization could be set in the Broadcasting tab in the Camera Settings window in the Remote Access Additional Settings window on the remote computer.
If the Remember Password check box is checked, the user name and password will be saved among the session parameters.

Cycle through cameras
If you have multiple cameras you can set up a cycler to have the program to change cameras automatically.

To configure the Camera Cycler:
  • Click Camera Settings from the File menu.
  • Select Cycle through cameras to activate cycler.
  • Type cycler interval in seconds.
Select cameras to cycle.

Jul 13, 2009 | HP USB Web Camera

2 Answers

What is the default ip address of D-Link DCS-3220 ip cam ?


Hello
The D-Link DCS-3220 have DHCP, that means it gets a automatic address from your router.
IT doesent have a STATIC ip, if you not set it manually.

To configure your D-Link DCS-3220 CAM and find the IP you need to install this program.
Install Wizard You need to unpack it first.

Connect your computer and cam to same router and run the program. Then it should find your cam so you can configure it and see what ip it get your you set.

Then you can browser to the cams IP.

Here is the manual and instruktions for you CAM

Here is Quick install guide

Here is you Dlink cam site to get firmware updates and more.

Hope it works.

Jul 09, 2009 | D-Link DCS-3220 Network Camera

1 Answer

Need BL-C30 installation exe file.pls hlp


Thank you for contacting Panasonic. We apologize for the delay in our response.

The CD can obtained through our parts department at 1-800-332-5368 or through the link below:

http://www.pasc.panasonic.com/epartr/

It can also be downloaded at http://netcamdealer.com/resources/file/82/103

The CD-ROM is not needed for setup. To setup the camera, type in the local IP address of the camera. If you do not know the IP address of the camera, press the reset button on the back of the camera to reset the IP address. This will default the IP address to http://192.168.XXX.253, with the XXX being replaced by the 3rd octet of your router IP address. For example, if your router IP address is 192.168.0.1, you will type
http://192.168.0.253 into your internet browser and you will be able to configure the camera. Another example is if your router IP address is 192.168.1.1, you will type http://192.168.1.253 into your internet browser and you will be able to configure the camera.

To obtain additional assistance for your product, please contact our Panasonic Customer Call Center at 800-272-7033. The hours of operation are Mon. - Fri. 9A.M to 9PM and Sat. - Sun. 10A.M to 7PM Eastern Standard Time. A representative will be available to assist you. Please have your case number 26813996 available at the time of the call.

Thank You,
Panasonic Consumer Support

Apr 13, 2009 | Panasonic BL-C30A Network Camera

1 Answer

How to reset to Default settings


turn on the camera, pressed holding the reset button.

Feb 10, 2009 | Sony SNC-RZ50N Network Camera

5 Answers

Veo network camera


The software is on the camera, all you have to do is connect it to your network and let it get an IP address, after it shows an address on the side window, use internet explorer to go to that address ( 192.168.1.XXX) or whatever the mask is for your network, make sure internet explorer is set to allow activex controls downloading, the browser will download the control and ask for password and user name, the default is "password" and "admin" good luck

Jul 07, 2008 | Veo Observer Network Camera

2 Answers

IP camera keeps resets itself


Hi

I have a pretty good knowledge of these cameras as I have 5 around my house.....

IP address resets are likely caused by the default address being loaded (192.168.0.99) and the box is not checked to reset the IP on reboot. You have two options.....

Using IP surveillence, open the camera settings. You will be prompted that the recording will stop, just press OK. Once you get to the settings window, you should see your list of cameras and the config screen for the one that is highlighted. Pick the camera you want to change the setting for and go to the tab where you can assign the IP address and gateway. Type in the IP address you want it to use. Uncheck the box that says 'reset IP on reboot'. That box is at the top. Hit apply. Once you do that, cycle the power on the unit leaving it off for at least 10 seconds. When the camera reboots, type in the new IP and you should be able to view it. (sometimes the camera will default on that IP if your router is using 192.168.0.1 and DHCP for computers that has that IP in it's range of assignments of IPs. Telling the camera which one to use and telling it to not reset on reboot will make the new IP stay in the camera.)

Your second option is to use the Installation Wizard or IE, find the camera either by typing in the IP for the camera in IE with the http:// or linking to the device with the installation wizard. If you follow the same procedure of assigning the IP and unchecking the box on reboot like described earlier, this should cure your problem. You do NOT want the IP resetting on reboot unless the camera will not link to your home router (likely causes for this is the IP range the router uses, say 192.168.1.1 like most belkin or linksys routers use, does not cover the IP range of the camera in it's DHCP server.

What I found best was to buy a junk router, set it's DHCP IP range to cover 192.168.0.99, set the camera, save it, kill the cameras power, connect it to the router you plan to use, then start the camera back up. Make sure whatever IP address you use on the camera is one covered by the DHCP server list on the router. ie: camera is set to 192.168.2.2 and the router assigns IPs from 192.168.2.2 through192.168.2.254. If your router only assigns IPS from 192.168.2.100 through 192.168.2.200 and the IP on the camera is 192.168.2.2, you won't be able to connect to it.

Hope this helps

May 19, 2008 | D-Link DCS-3220 Network Camera

1 Answer

Networking the intellinet 503181


Hello,
There are a couple things to check. Make certain that you have port forwarding enabled for port 80/80 to the IP address of the camera. Make certain that you have port forward for port 8080/0 to the IP address of the camera. Find your IP address for your Internet connection - you can go to ipchicken.com and it will display your IP address for you. Then open your browser, type in your Internet IP address on the address line and hit enter. That should bring up the guest log in window and you can log in to view the video stream. If you want to log in to the camera console to change configurations, just type the camera user name and password instead of the guest user name and log in.
Hope this helps!

Dec 31, 2007 | Intellinet Active Networking 550703...

2 Answers

Password and user id


Reset the camera by holding the reset button for 3 seconds (use a paper clip in the hole marked "Reset" on the back). The camera will then reset to all default settings, including an IP address of 192.168.0.20.

Nov 19, 2007 | D-Link DCS-900W Network Camera

Not finding what you are looking for?
Swann Communications Opti-Viewcam Webcam Logo

Related Topics:

462 people viewed this question

Ask a Question

Usually answered in minutes!

Top Swann Communications Computers & Internet Experts

Christopher Thrash

Level 3 Expert

425 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

vimal
vimal

Level 3 Expert

340 Answers

Are you a Swann Communications Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...