Question about Kenmore 3.2 cu. ft. Top Load Washer
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
REplace your MCU. The MCU is the Drive Motor Control board and is located in the rear of the washer adjacent to the Drive Motor on the left-hand side (facing from the rear with the back panel removed). The wiring harness can also cause the error, but it is not as common a problem. Go onto kenmore.com and find your right washing machine and replace the part yourself. First try and take the wiring harness off and then reconnect it and see if the error code goes away if it doesnt then replace the part. Please Rate. Thank you
Posted on Feb 12, 2009
F 30 code can be reset by un plugging power cord for 5 minutes also pull out the detergent dispenser and reach all the way in to the back there is a small plastic flapper valve move it from side to side with your finger this will rest code f30 and save a tech visit..
Posted on Nov 11, 2008
See if this helps.
Posted on Aug 01, 2009
SOURCE: Kenmore Elite error message F 02
Here is what the manufacture says about F02 - Below this are my comments
If the drain time exceeds eight minutes, the water valves are
turned off and “F/02” is flashed.
Press PAUSE/CANCEL two times to clear the display.
NOTE: After four minutes the “Sud” error will be displayed,
then four minutes later the “F/02” error code will be
Possible Causes / Procedure
1. Check the drain hose and make sure it is not plugged
2. Unplug washer or disconnect power.
3. Check the electrical connections at the pump and make
sure the pump is running.
4. Check the drain pump filter for foreign objects.
5. Plug in washer or reconnect power.
6. If the above does not correct the problem, go to step 7.
7. Unplug washer or disconnect power.
8. Replace the pump.
If you washed a rug with a rubber backing or small articles like baby socks you may have a plugged up pump. To access the pump lay on the floor and remove the 3 screws holding the lower panel of washer on. Pull down and out on the panel to remove. Lay out a lot of towels under the unit, I mean a lot... Look in the center for a white cap about the diameter of a large cup, it will have a handle on it to turn, turn this left(counter clockwise) to unscrew. This will unscrew and pull out, but be careful when it comes out so does all the water. Clean out the trap that is in your hand and anything you see or feel in the sump area the trap came from. Reassemble and test. If this does not work you will more than likely need a new drain pump, that is the component on the right of that trap you just cleaned out.
Posted on Apr 20, 2010
Testimonial: "You are a Guru! Thank you so much for informing us about the "hidden" trap which housed an ankle sock, .90 & lint! works like a charm now!!"
Tips for a great answer:
May 12, 2012 | Kenmore Elite Oasis 6808 Electric Dryer
May 15, 2010 | Kenmore Elite HE4 Electric Dryer
Aug 16, 2009 | Kenmore Elite 21086
Aug 01, 2009 | Kenmore Washing Machines
Jun 23, 2009 | Kenmore Elite 45986 Front Load Washer
May 22, 2009 | Kenmore Elite Oasis 27052 Top Load Washer
Mar 12, 2009 | Kenmore Elite 45986 Front Load Washer
Jun 21, 2006 | Kenmore 23822 Top Load Washer
Aug 01, 2011 | Kenmore 3.2 cu. ft. Top Load Washer
Jun 27, 2011 | Kenmore 3.2 cu. ft. Top Load Washer
May 15, 2011 | Kenmore 3.2 cu. ft. Top Load Washer
109 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: