Question about Baxter Ovens

Open Question

How do I replace the door gasket in the baxter oven model: ov210g2

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3230 Answers

SOURCE: i am looking for the

Hi there,

Well first of all please tell us the Model number of your Oven, so we can help you in details.........

Thanks

Posted on Jan 05, 2010

Ad
  • 193 Answers

SOURCE: I need to replace the

Cadco sells parts to the end use through a parts distributer. The phone number is 800 458 5593. Have your model and serial number ready when you call.

Posted on Oct 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need wiring digram for baxter oven ov300e


Request the wiring diagram directly from Baxter.

Feb 23, 2017 | Baxter Ovens

1 Answer

I need owners manual for a baxter model pb200 m90


YOU CAN PROBABLY FIND ON ON LINE. TYPE IN BAXTEDR MODEL PB200M90 MANUAL OR MANUAL FOR BAXTER MODEL PB200N90

Jan 28, 2015 | Baxter Ovens

1 Answer

Baxter oven not working


Hobart owns Baxter. You'll have to call Hobart.

Feb 14, 2014 | Baxter Ovens

1 Answer

How do I fix the flame sensor in a baxter oven?


Take off the right side panel and open the control panel door. Take a long screw driver and stick it in the hole where the flame sensor wire goes and remove the screw holding the flame sensor in place. Clean the metal rod on the flame sensor with a piece of fine grit sandpaper or emory cloth. Put flame sensor back in, make sure no insulation is touching the exposed metal part of the wire connector.

Feb 24, 2012 | Baxter OV300E Stainless Steel Electric...

1 Answer

I will need to get a Baxter OV300EDD oven through a 35" wide door frame. Considering the oven is 37.49" deep, could I remove the doors off the front of the unit so that it will fit through the...


You can remove the oven doors, hinges, control panel door, and top oven trim, if needed. That will definitely reduce the width enough to squeeze it in.

Aug 17, 2011 | Baxter OV300E Stainless Steel Electric...

1 Answer

Wich is the power supply 120v, 208 1 phasse or 208v 3 phase.


Most Baxter BXA ovens have separate power supplies, usually 120v for the controls and lights, a 120v output on a circuit breaker for the roof fan, and a 208VAC 3 phase supply for your convection motor. Older Baxter ovens may have a 3 phase service disconnect inside the electrical/burner compartment, if I recall correctly the BXA models do not and the only way to shut it off is via the 3 pole breaker at the service panel.

Feb 04, 2011 | Baxter BXA2G Stainless Steel Gas Single...

1 Answer

I have a Baxter oven OV210G, When the door is open the rack will not stop or lower. The micro switches all work and relays seem to work but I can't find the MR3 cantactor and don't if that is the problem...


When you open the door check to see if your burner and circulation fan remain on, if they do you have an issue with your door switch.
Also if your rotation micro-switch was bad you would get a buzzer every 1 second because the oven would think the carrier isn't rotating.
It's hard to troubleshoot beyond that without seeing the oven, its possible you could have a bad relay on your control board. In this case I would call an authorized service provider to have to check the oven out.

Dec 07, 2010 | Baxter BXA2G Stainless Steel Gas Single...

1 Answer

Serial Number location


EITHER TOP LEFT CORNER OF OVEN< or UNDER PANAL take off the one screw panel opens right upo like door, Right there!!

Jul 12, 2010 | Baxter OV300E Stainless Steel Electric...

1 Answer

When we turn the switch on, the light inside the oven goes on, but the touch pad does not come on, it comes on by itself after a while, or will shut off in the middle of cooking.


Control board defective. Before replacing the control board make sure that your incoming water pressure is no higher than 20 psi and that your door gaskets and fan seal is intact. Torn gaskets or a worn fan seal will allow steam to enter the burner compartment and damage your control board.

Sep 12, 2009 | Baxter OV300E Stainless Steel Electric...

Not finding what you are looking for?
Ovens Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Baxter Ovens Experts

Owen Barnes

Level 3 Expert

867 Answers

ray gallant

Level 3 Expert

47630 Answers

yadayada
yadayada

Level 3 Expert

77186 Answers

Are you a Baxter Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...