Question about Samsung Digimax S500 Digital Camera

1 Answer

Where is the flash control

I dont know what to push or what to look for to know the flash is on

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Samsung Master
  • 102,366 Answers

Press cursor-left to cycle through the various flash modes. See page 21 of this manual.

Posted on Jan 14, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set clock in radio on a 2014 Jeep Patriot


Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save the time change. 5. To exit, press any button/knob or wait five seconds http://www.chryslercommercialvehicles.com/jeep/download/pdf/manuals/2014-Patriot-OM-1st.pdf page 240

Mar 12, 2015 | 2014 Jeep Patriot

1 Answer

My t.v. dont stay on


Hi,

First do a hard reset. Merely unplug the power cord for 4 hours, then restart it. This will correct it if the cause is corrupted soft codes.

If not, the protection circuit has captured the power management and you must have it looked at by a service tech.

Let me know if there is more.
Dont forget to rate me as fixya..

Jan 30, 2008 | Mitsubishi WT-42311 42" Rear Projection...

1 Answer

I have a Shapr Microwave Convection model R-8880(W) T which is flashing after being stored for 3 months. It won't work, the timing light just keeps flashing on andoff 88-888. Does it have a reset...


Try pushing / stop reset first. The setting the time by pushing clock button .... punch in the time and push the clock button again. Just respond here if that does not work. 88-8888 is what you get after your first plug it in. Sometimes you will get PF if you unplug it and plug it back in. If that appears push stop / reset / clear. (Same button)

Kelly

Dec 26, 2010 | Sharp Microwave Ovens

1 Answer

Wot do i do after entering my code on a 5000 rds


Radio should start straight away.
If it is the same as the 3000 series , the numbers are entered as numbers of times you push sequential keys. ie: code 1579 , push number 1 once, push number 2 five times, push number 3 seven times and push number 4 nine times.
If the display is flashing " ERR " you will need to leave the ignition on until it stops flashing and the display reads " CODE" . ( it can take up to an hour)
Hope this helps.

Apr 08, 2010 | 2000 Ford Focus

1 Answer

On the screen there is a picture with a camera and exclamtion mark i dont know what it means


It's a low light level warning. Push the button on the left side of the flash to pop up the flash

Nov 30, 2009 | Fuji FinePix S1000FD Digital Camera

1 Answer

My remote flashes but i dont know how to connect it i have never done it before and dont have a manual


umm you have to open up the latch on the front of the console and remove the cover of where you place batteries in your controller. both places should have a red button. Push the button on the console first then the button on the controller.

Oct 02, 2009 | Nintendo Wii Console

1 Answer

I dont know how to pair the ps3 controller to the ps3, the light comes on tho


push the button on the system at the same time as you push the button on the controller

Jun 11, 2009 | Sony Playstation 3 (PS3) Console

1 Answer

All flash lihgts are flashing and priner dont work


Hi

have you tried turning it off and unplugging it for a few minutes? pls keep us posted.

Thanks

Nov 14, 2008 | Epson Stylus Color 3000 InkJet Printer

1 Answer

Lights dont come on


If you have a Craftsman/Liftmaster with a 3 function wall control:
use the lift button to turn the light off. push and hold the light button for @1min. until the light flashes. This should reset your operator to have the light turn on when you walk through the photo eyes.

Oct 21, 2008 | Chamberlain Powerdrive PD422D 1/2 HP...

Not finding what you are looking for?
Samsung Digimax S500 Digital Camera Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Cameras Experts

kakima

Level 3 Expert

102366 Answers

Cindy Wells

Level 3 Expert

5184 Answers

Kazim ERGUNEY
Kazim ERGUNEY

Level 3 Expert

577 Answers

Are you a Samsung Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...