Question about Stanley 77 115 Intellisensor Plus Stud Sensor

Open Question

Unable to Calibrate stanley s100 stud finder - Stanley 77 115 Intellisensor Plus Stud Sensor

Posted by Anonymous on

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stanley stud finder AC sensor continually beeps on 10mm plasterboard wall


Most stud finders have a sensitivity adjustment that should be carefully adjusted per instruction manual before use.
Failure to do this results in erroneous indications.

If you have adjusted exactly per the instructions with the same result the unit is probably faulty.

Sep 22, 2017 | Stanley Measuring Tools & Sensors

1 Answer

Stanley instructions


Try using a magnet instead. Move the magnet back and forth against the wall, slowly... until it sticks to one of the ferrous screws hidden in the sheetrock. These hidden screws are holding the wall board/sheetrock onto a stud.
Magnets! Free stud finder! and no batteries to replace!

Aug 26, 2014 | Stanley 77 500 Intellilaser Pro Stud...

1 Answer

How to use a stud finder


The stud finder works by picking up density of the product it is pressed and slid on..Turn your stud finder on make sure the ok light is on...then slightly press it against the wall or surface you are working with,,then slowly moved it right or left still against the surface. As the finder starts to detect more density "thickness" it will. Glow or beep depending what type you have..It will get brighter,louder or what ever it signals are while crossing the stud beneath the surface..keep moving until it stops then move back
again until it stops.....mark or note the position where the signal starts then find the middle...2x4's are 1 1/2 inches across...so center should be 3/4 of an inch...good luck..

Aug 04, 2014 | Stanley 77-720 Stud Sensor 200

1 Answer

How to use stud finder


While holding the stud finder on a spot on the wall where you assume there is no stud... press the button and hold and stay still for 10 or 15 seconds to calibrate. Then while still pressing the button start sliding sideways until the lights indicate the thickest point. You can use a pencil to mark the beginning and end. The center of that is the center of the stud. Measure 3/4 of an inch left and right of it to know it's sides.

Nov 24, 2013 | Black & Decker Distance Measurer with...

1 Answer

Stanley fatmax s300 manual


Go to http://www.youtube.com/watch?v=QInszVD9WpE&feature=youtu.be - doesn't tell you everything, but better than the manual Stanley ship with the product, which is just a collection of hard to decipher graphics.

Feb 03, 2013 | Stanley Measuring Tools & Sensors

1 Answer

Instruction for Stanley FatMax Stud Sensor Finder 400 (77-730)


Please people dont waste your money but a cheap standard one Stanley 77-730 stud finder is bad does not work at all , miss my old cheapy never failed me

Mar 05, 2012 | Stanley Measuring Tools & Sensors

1 Answer

How do i callibrate a draper 63401 detector.regard.


I have never met a stud finder that needed calibration. They should auto calibrate when you begin to search for a stud. Recalibrating is starting the search again. Start in a different location on the wall to get a different calibration. This particular stud finder has bad reports on amazon.

Jun 11, 2011 | Garden

1 Answer

I have plaster walls in an old house the stud finder just keeps beeping how does this thing work?


Your stud finder keeps beeping because old plaster walls have lath boards behind the plaster that are attached to the studs and running horizontally. Try adjusting the sensitivity of the stud finder by placing it on the wall and turning the sensitivity down until it just stops beeping. Then move it back and forth in a wide enough arc to be sure that you have crossed a stud, turning up the sensitivity ever so slightly until you get a tone when you cross a stud. Hope this works out for you.

May 08, 2011 | Stanley Garden

1 Answer

How to operate the Stanley Stud Finder


Hi Gene,

  • Place the unit flat against the wall.
  • Press and hold the button.
  • The LED will come on for a second or two then go out.
  • Slowly move the unit laterally until the LEDs come on again.
  • When they top out, that is the beginning of the stud.
  • When they start to go back down, that is the end of the stud.
That's about it..

Best regards
Mike

Jun 04, 2010 | Stanley 77 115 Intellisensor Plus Stud...

Not finding what you are looking for?
Stanley 77 115 Intellisensor Plus Stud Sensor Logo

Related Topics:

1,462 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanley Measuring Tools & Sensors Experts

Lawrence Oravetz

Level 3 Expert

9845 Answers

Vernon Taylor

Level 3 Expert

3921 Answers

Steve

Level 3 Expert

3289 Answers

Are you a Stanley Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...