Question about Jacuzzi BK37959 White Era?? Two-Piece Elongated Toilet BK37

1 Answer

Jacuzzi toilet does not fill enough water in the bowl

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 979 Answers

Check to see if there is not a clog in the trap. This could keep your bowl from filling up. Also check the flapper and see if it is staying afloat in the tank long enough during the flush. Either of these could be the cause here.

Posted on Feb 04, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

slave2aslave
  • 302 Answers

SOURCE: installing new jacuzzi 1.6 gallon maxima toilet.

Sounds like you need a new gasket. Turn off the water,empty the tank,remove the bolts from the underside of tank,lift tank off,replace gasket,or check to see if the gasket has been installed correctly. Does the gasket look like it was compressed straight? If not then you can attempt to re-seat with the same gasket,but if it still fails to seal you'll have to buy a new gasket.

Posted on Oct 06, 2009

jeff_drakesr
  • 155 Answers

SOURCE: how to assemble tank to bowl

  1. Place the Rubber Donut on th bottom side of the tank (this will form a seal from the tank to the bowl)
  2. There are two small holes to either side this is for your two tank bolts. Place a washer on both bolts and place them in the two holes with the head of bolt and washer inside the tank. Place tank on bowl, matching up the holes.
  3. there are two plastic nuts that are beveled on one end, with bevel up toward bolt head thread onto bolt finger tight. Repeat for remaining bolt.
  4. Apply a little pressure to one side of tank and tighten nut finger tight again then repeat for other side. May need to do this a couple of times back and forth. IMPORTANT tight the nuts equally and carefull not to overtighten or you will crack the tank ONLY FINGER TIGHT.
Good Luck and have a Great Day. Please give a 4 THUMBS UP if this free answer was helpful. THNX

Posted on Apr 01, 2010

  • 349 Answers

SOURCE: I have a Jacuzzi Perfecta toilet (bought Aug. 21,

Have you tried shutting water off and take top of valve appart and flush it out. It may have something in valve causing water to be restricted. It will have an arrow on it to direction to get it to come off.

Take appart and clean rubber disc and you can put something over top of valve , a small cup or something to enable you to flush the tank. Have someone help you and hold the cup above the valve so that when you turn water on for a few bursts to flush out the valve it goes into tank.

The actual stream that flows through valve is restricted down to almost 1/8 " opening so it wouldn't take mush to block the flow of water.

The disc you take out you can replace it, if it seems to be damaged and not working correctly. That will affect the flow also.

Posted on Jun 10, 2010

Testimonial: "I took the valve apart. It is working like it is supposed to. That sure is a tiny hole for the fill water to shoot through. that is why it is so slow. It still whistles when filling. Tnx Walter Neaves"

  • 760 Answers

SOURCE: please tell me how to get more water in my toilet

The water level in the bowl is determined by the built in trap in the back of the bowl. Water is allowed to enter the toilet and it then "over flows" the p trap in the back when flushed. Once it's flowing, it syphons the water out of the bowl. While the tank is re-filling, a small portion of water should be running down the overflow from the small hose clamped onto the overflow This rinses the inside of the bowl, as well as helps-refill the bowl. Be sure that hose is directed inside the overflow tube. To see what the max water level in the bowl can be, add some water from a cup or glass. Once it's full you can keep adding and it won't get any higher. This will be the max level you can expect.

Posted on Jul 07, 2010

  • 177 Answers

SOURCE: We have a Jacuzzi X532 toilet. Can't get the water

I am not familiar with the model of toilet that you have, but many toilets suffer the same problem. It is usually due to the toilet cistern over-filling, as the water running into the bowl is the safety-overflow mechanism. The overfilling can be for a few reasons. The most common is that the fill valve is being held open, either due to mal-adjustment, or due to it being postioned slightly wrongly so that it hits either the side of the cistern or another part of the mechanism and can't close off properly. If you lift off the top of the cistern and watch what happens when the flush goes, you might be able to spot what is preventing the valve from shutting off entirely, and solve it. Hope this helps! :)

Posted on Jul 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't get enough water in toilet bowl to flush the waste


Adjust your tower to let the bowl fill up more.....google your problem if you dont understand...depends on what kind of tower you have....should have teeth on the tower itself to make it fill more...try pulling up on the float...

Mar 15, 2012 | Jacuzzi Bath Perfecta EZ33 959 White round...

1 Answer

My jacuzzi toilet doesnt fill with enought water in the bowl to remove waste from porcilin when flushing


Hi, W/D here.
Check the water level in the tank. The force to flush waste comes from there. Normally the fill line is cast into the back of the tank, but sometimes it is on the overflow tube. Raise the level if it is low.
Also, make sure that the tubing from the fill valve is connected to the over flow tube (the tall tube).
Best regards, --W/D--

Jan 29, 2011 | Jacuzzi Bath Era BK37 959 White toilet...

1 Answer

We just brought a Jacuzzi toilets and find that there are not much water in the bowl (3 inch deep). Can it be adjusted to have more water in the bowl ?


You cannot adjust the standing water level in any toilet bowl..That level is designed in. To verify what has been designed into the bowl just add water. Take a large pot full of water and just dump it dierctly into the bowl. Whatever level you end up with is by design.

Oct 23, 2010 | Jacuzzi Home

1 Answer

We have a Jacuzzi X532 toilet. Can't get the water to stop running into the bowl, causing excess water usuage and stains intoilet bowl. This started about two weeks ago. Have this toilet approx. 3-4...


I am not familiar with the model of toilet that you have, but many toilets suffer the same problem. It is usually due to the toilet cistern over-filling, as the water running into the bowl is the safety-overflow mechanism. The overfilling can be for a few reasons. The most common is that the fill valve is being held open, either due to mal-adjustment, or due to it being postioned slightly wrongly so that it hits either the side of the cistern or another part of the mechanism and can't close off properly. If you lift off the top of the cistern and watch what happens when the flush goes, you might be able to spot what is preventing the valve from shutting off entirely, and solve it. Hope this helps! :)

Jul 19, 2010 | Jacuzzi Home

1 Answer

Please tell me how to get more water in my toilet bowl..not the tank..the bowl please..thankyou. It is a Jacuzzi Era Elongated bowl.


The water level in the bowl is determined by the built in trap in the back of the bowl. Water is allowed to enter the toilet and it then "over flows" the p trap in the back when flushed. Once it's flowing, it syphons the water out of the bowl. While the tank is re-filling, a small portion of water should be running down the overflow from the small hose clamped onto the overflow This rinses the inside of the bowl, as well as helps-refill the bowl. Be sure that hose is directed inside the overflow tube. To see what the max water level in the bowl can be, add some water from a cup or glass. Once it's full you can keep adding and it won't get any higher. This will be the max level you can expect.

Jul 07, 2010 | Jacuzzi BK37959 White Era?? Two-Piece...

1 Answer

Bowel cleaning


Check the ports under the rim and make sure they are not clogged. To do this you can use a nail or pin to clean them out.
Right under the rim of the bowl are these ports that allow the water to flow into bowl in a turning motion to aid in flushing and cleaning wall's of the bowl.
Inside the tank check the fill tube and make sure it is connected from the fill valve to the over flow tube. Also check the fill level in the tank and make sure water is up to the line on the fill tube about 5/8" from top of tube.

Jun 06, 2010 | Jacuzzi Bath Perfecta EZ33 959 White round...

1 Answer

The water level in the toilet bowl is too low. Can I adjust the level, and if so, how?


Too little water in the toilet bowl to start with may be due to a lost or mis-connected fill tube that directs some water into the toilet tank standpipe (and thus into the bowl below), while the toilet tank is being re-filled. Check for that little tube.

Check the web site out below for more information on this topic.

http://www.inspectapedia.com/plumbing/Toilet_Slow_Flush.htm

May 23, 2010 | Jacuzzi Maxima DP55959 White Toilet Bowl...

1 Answer

Water level drops in bowl after it fills


If very little water is used on initial flush, The bowl is functioning as a tank for second thorough flush. The high water level cannot stay high in the bowl while in motion or you would have a mess ion start and stops.

May 28, 2009 | Jacuzzi Bath Perfecta EZ33 959 White round...

1 Answer

Water level drops in bowl after it fills


Replace your stopper at the bottom of the tank. While you do hat you should also just go ahead and replace the float. 25 dollars for everything and 10 minute worth of your time

Feb 14, 2009 | Jacuzzi Bath Perfecta EZ33 959 White round...

Not finding what you are looking for?
Jacuzzi BK37959 White Era?? Two-Piece Elongated Toilet BK37 Logo

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jacuzzi Home Experts

Mike

Level 3 Expert

4336 Answers

john h

Level 3 Expert

11039 Answers

Donni Steen

Level 3 Expert

659 Answers

Are you a Jacuzzi Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...