Question about Dremel 1830 120V 18" Scroll Saw

2 Answers

I want to know service center for Kodak Easy share C743 in Mumbai, India.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Shivaji Park Photo Studio & Color Lab (Kodak) Rate it
252/A Vawada Building, L J Road, Dadar East, Mumbai, 4










Upgrade to Sponsored Update Report Error Add Pictures Write Review




:

Posted on Jan 23, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

If you would be my pen pal I will answer you. You are adorable

Posted on Jan 23, 2009

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I was using my Black & Decker 10 in. Delux Table Saw and went to shut it off after cutting the piece I needed. Flipped the switch to off and the saw wouldn't stop.


Hi-

I'm sorry to hear that your saw would not turn off. This sounds like a possible switch issue and would need to be looked at by a service center. I would encourage you to stop use of the saw until it has been checked out. Please follow the link to locate your nearest service center. blackanddecker com

Thanks
Black + Decker Customer Care

Feb 24, 2015 | Black & Decker Table Saws

1 Answer

I have a bosch 4000 the motor is smoking and growling (like a bearing is going bad)


If the motor is smoking, yopu should not use it further. If it is a universal motor with carbon brushes, inspect the brushes for wear and replace. If the bearing is going bad, it has to be replaced. There is no easy fix for a bad bearing, except to replace it. You best bet would be to take it to a Bisch approved service center, or call them and get an estimate cost on repair. If too high it may not be worth repairing it over the cost of a new saw. If it is still under warranty, then demand for it to be serviced/repaired as part of that warranty.

Feb 28, 2011 | Bosch 4000 - 07 Electric Table Saws

1 Answer

I'm thinking of purchasing a Craftsman Model 113.29901 (circa 1970) table saw in good condition from an older carpenter that used it for cabinet work. It has 4 - 10" ext'ns with it. It has a little surface...


I can't tell you what the value is but I can share a tip I use whenever buying a used saw.

With the saw in the 90 degree position (Straight up) run a board all the way through the board. Then flip one half of the board upside down and place the two cuts together. If the blade is true the two halves should line up perfectly. If they don't that means the blade is out of square. While re squaring a saw is fairly easy, I would wonder why the blade was off and how often that would happen and therefore would likely not buy the saw.

Of a side note, Craftsman does make a great saw and they are fairly easy to work on and find parts for.

Good Luck

Oct 16, 2009 | Powermatic 1791227K Model 64 10" Artisan...

1 Answer

Where do I find a replacement motor for a 1313314 Delta table saw? Wont take a load, keep turning off and smells hot?


Hi there
You can try the website @ http://www.deltaportercable.com/ to see parts list and find service centers near you .
Delta , Porter Cable and Dewalt are together so you can get parts thru Dewalt parts center .
Hope this help

Aug 31, 2009 | Table Saws

1 Answer

We need the wiring configuration for the switch.


Contact a dewalt service center and they should tell you over the phone which wire should go where. I see that it has 3 prongs in the parts brake down. Most of the time the wires only reach one way. Here is a link to find your local service center.

http://www.blackanddeckerservicenet.com/servicenet_home.aspx?AspxAutoDetectCookieSupport=
1

Apr 03, 2009 | Table Saws

1 Answer

How do you remove the arbor assembly on a craftsman 10" table saw


go to sears service center and get a new arbor, and ask them to show you the motor and arbor assembly drawing. it should show how the arbor is attached to the shaft.
you can pull the arbor off with a pulley. you can get that from auto parts store.

Mar 31, 2009 | Craftsman 10" Table Saw

2 Answers

The motor on my 4000 Bosch table saw burnt out


Contact Bosch for authorized repair centers near you. if you are handy with tools, you maybe able to replace the motor youself. If you happen to live in Nebraska, there is a guy in Kearney that repairs all makes of tools.

Mar 22, 2009 | Bosch 4000 - 07 Electric Table Saws

1 Answer

Nut thread is stripped


This is an older saw and DeWalt does not have it online to check parts. They suggest that you contact a local service center for that information. I also tried a couple other sites that sell replacement parts with no luck. If you cant find it let me know and I am in contact with a local Dewalt center where I work and will call them for you.

Dec 25, 2008 | Black & Decker Dewalt DW3123 12" x 32 and...

Not finding what you are looking for?
Dremel 1830 120V 18" Scroll Saw Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dremel Table Saws Experts

EugenesDIYDen
EugenesDIYDen

Level 3 Expert

479 Answers

John Trevino

Level 3 Expert

1378 Answers

Mike

Level 3 Expert

4331 Answers

Are you a Dremel Table Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...