Question about Equator EZ 1612 V Front Load Washer / Dryer

1 Answer

Door handle for Equator EZ 1612 V

Where can I buy the door handle for washmachine Equator EZ 1612 V

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

    Governor:

    An expert whose answer got voted for 20 times.

  • Contributor
  • 37 Answers

If you are still waiting for this part you can purchase it from www.appliancedesk.com click on shop parts.

Posted on Feb 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Equator Washer dryer combo......door wont open. Finished a funky cycle drained but wont open? :(


You will have to follow the drain out procedure and then the reset procedure.
Please see the link :http://www.fixya.com/support/r4240518-door_not_opening_in_equator_hirundo

Be careful, if you try to open the door by pulling the door handle too hard it may break.
Do let me know if this resolves the problem or else I may suggest something else.

Mar 26, 2010 | Equator EZ 3612 CEE Front Load...

1 Answer

My equator EZ 2512 CEE washer/dryer suddenly wont finish washing a load of laundry. I think some sort of drain pump may be broken. The door will not unlock. I took the drain hose out and put it on the...


If you are still looking for a solution to this here it is:
In these machines if you try to change the setting of the washer knob without letting a cycle finish which is already set it may happen that the unit won't function properly and hence the unit needs to be reseted. There is a reset procedure for the same and let me know if you would like have the same.
If the door is not opening it is advisable to reset the unit first and then try opening the door which should work and also the door handle won't break then.
If you have already replaced the door handle on your machine it is fine or else you may want to order the same from appliancedesk.com

Nov 22, 2009 | Equator EZ 2512 CEE Front Load Washer /...

1 Answer

Any advice on how to reinstall the door on one of these? I took it off after breaking the handle...but the threaded backers that held the screws in fell down into the machine...


unplug 1st/ partly tip machine put in hand retreive screws backplate/ you may require to partly remove door seal to refit this ..Good luck

Nov 12, 2009 | Equator EZ 1612 V Front Load Washer /...

1 Answer

Need door handle for EZ 1500


This is one of the oldest model sold by Equator and the factory who manufactured this model have stopped producing any more parts for this model including a few others and there is no other company carrying the parts for these models and hence it is not possible to get these parts any more.

Apr 22, 2009 | Equator EZ 1500 Front Load Washer / Dryer

1 Answer

I need a diagram of an Equator EZ3612CEE door


While you may have removed the door with the hinges from the cabinet the nuts may have fallen down on the unit.
You may want to open the back panel or the bottom panel and try searching for the same, in case you need assistance mounting the bracket back on the cabinet once you have the nuts do let me know.

Nov 24, 2008 | Equator EZ 3612 CEE Front Load...

1 Answer

Equator door handle


Here is the phone number for equator, 1800-935-1955 or parts and service 800-776-3538. They sould be able to help you.
Their address is 10067 Timber Oak Dr. Houston, TX 77080-7045

Jun 27, 2008 | Equator EZ 2512 CEE Front Load Washer /...

2 Answers

Handle


I order mine online from appliancedesk.com. I have one ordered now. It is on backorder. When you install new, be sure to mark position of door inserts, just in case they separate and you have to figure out how to reposition them.

Apr 09, 2008 | Equator EZ 3612 CEE Front Load...

8 Answers

Broken door handle...


I have the same problem and I have a makeshift solution which I was able to do in 45 minutes and total cost was less than $1.

Step 1: Remove door from machine.
Step 2: Disassemble door with the two plastic donut shells. This means removing 6 or so flathead screws. Take care to note alignment of glass parts because they aren't perfect circles and only fit one way.
Step 3: Pull out pin that threads the spring and broken plastic handle remnant and metal latch piece.
Step 4: Discard broken plastic and replace the rest of the apparatus. The metal latch can move up and down, but that's ok.
Step 5: Purchase a paint-can opener:
http://www.istockphoto.com/file_thumbview_approve/525566/2/istockphoto_525566_opener_for_paint_can.jpg
Step 6: Re-attach door.
Step 7: You can use the paint-can opener to the right of the latch to lever-open and lever close the latch in order to open and close the door.

Cheap, easy. Not pretty at all. Definitely something your friends would make fun of you for doing, but it saves you $1,000 of a new machine, in this economy.

Jan 19, 2008 | Equator EZ 3612 CEE Front Load...

1 Answer

Equator EZ3612 CEE


If you still need assistance on this let me know and I can provide you with the procedure for the same.

Sep 15, 2007 | Equator EZ 3612 CEE Front Load...

Not finding what you are looking for?
Equator EZ 1612 V Front Load Washer / Dryer Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Equator Washing Machines Experts

isaac johny
isaac johny

Level 3 Expert

796 Answers

Brad Brown

Level 3 Expert

13530 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you an Equator Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...