Not able to adjust convergence

If the following doesn't work the tubes could be at the end of life:
Adjusting convergence:
Note: For best results, the Projection TV needs to be turned on for 15 minutes or longer before adjusting the picture tubes (convergence).

To adjust the convergence of the picture tubes:

1. Press the 'MENU/SELECT' button on the remote.
2. Press CURSOR RIGHT to enter the PICTURE menu.
3. Use CURSOR DOWN and RIGHT to select and enter MANUAL CONVERGE.
4. Press CURSOR RIGHT to select CONVERGE RED or press CURSOR RIGHT and DOWN to select CONVERGE BLUE.
5. A crosshair will be shown on the screen. If there is any red or blue fringe around the crosshair, use CURSOR RIGHT, LEFT, UP, DOWN to try and merge the fringe colors with the crosshair.
6. Press the 'MENU/SELECT' button to return to MANUAL CONVERGE menu.
7. Press the 'EXIT' button to exit the menu.

If you are satisfied with the convergence you may stop now. Otherwise, you can continue and adjust the convergence more using mult ipoint convergence.
To Adjust multipoint convergence:

1. Press the 'MENU/SELECT' button on the remote.
2. Use CURSOR RIGHT to enter the PICTURE menu.
3. Use CURSOR DOWN and RIGHT on the cursor ring to select and enter MANUAL CONVERGE.
4. Press CURSOR RIGHT and DOWN on the cursor ring to select MULTIPOINT RED or MULTIPOINT BLUE.
5. A grid of crosshairs will appear on the screen. If there is any red or blue fringe around any of them, press CURSOR RIGHT to enter NAVIGATE mode.
6. Use CURSOR RIGHT, LEFT, UP, and DOWN to move to a crosshair that has a color outline.
7. Press the 'EXIT' button to enter ADJUST mode.
8. Use CURSOR RIGHT, LEFT, UP, and DOWN to merge the color with the crosshair.
9. Press the 'STATUS/EXIT' button to return to NAVIGATE mode. Repeat as necessary.
10. Press the 'MENU' button to return to the MANUAL CONVERGE menu.
11. Press CURSOR DOWN until SAVE MULTIPOINT is selected.
12. Press CURSOR RIGHT to save the multipoint settings.
13. Press the 'EXIT' button to exit the menu.

http://www.retrevo.com/support/Philips-46PP9302H-TVs-manual/id/278ci462/t/2/

The above link should take you to the location where you can view all the parts of your models manual. Select the area of interest and rad onlinje


Please rate my help++++Thanks for using FIXYA

This can be as simple as poor solder connections at the convergence ICs or defective ICs. If you can solder you can fiz this yourself. Let me know if you wish to attempt the repair and I'll suply additional details and instructions.

Dan

The convergence board is bad. If the convergence board were still good, then the convergence menu would allow you to adjust the crosshairs.

If your convergence alignment wont work by the convergence menu you have defective Convergence ICs for about 10.00 each there are two that need replacing. If you need any further assistance let me know.

Blue convergence IC is bad, but change both as red wont be far behind they are cheap about 10.00 ea at the following link.
http://electronix.com/

To adjust manual convergence on your projection TV, follow theses steps:

1. Turn your TV on.
2. Let it warm up for 30 minutes.
3. Press the Menu button on your remote. The Main menu appears.
4. Use your remote to select Function, and then press the joystick.
5. Select Convergence, and then press the joystick. The Manual Convergence screen appears.
6. Select Red, and then press the joystick. A series of crosshairs appears on the screen.
7. Select one of the outside crosshairs by moving the joystick up/down/right/left or by pressing the 2 (up), 4 (left), 6 (right), or 8 (down) buttons on your remote. The method you use depends on the model of remote you have. Note: You must do the outside crosshairs first.
   

1. In the crosshair you selected, if you can see a horizontal red line, use the CH up or CH down buttons to move the line so that it is superimposed on the horizontal center line of the crosshair. Note: Make the single horizontal line as white as possible.
   

1. In the crosshair you selected, if you can see a vertical red line, use the Vol + or Vol - buttons to move the line so that it is superimposed on the vertical center line of the crosshair. Note: Make the single vertical line as white as possible.
   

1. Repeat for all outside crosshairs, and then for the inside crosshair.
2. Return to the Manual Convergence Screen, and select Blue, and then press the joystick.
3. Repeat Steps 7 through 10 for Blue.
4. Press the Menu button on your remote to exit.

Important: The directions above work for most Samsung Rear Projection TVs. Yours may be different. For exact directions to perform manual convergence, see your user's manual. If you don't have your user's manual on hand, click HERE to view your manual on line.
If you cannot get your Projection TV to converge, it may need to be serviced. To arrange a service appointment, call Samsung Customer Care at 1-800-Samsung (1-800-726-7864). Have your TV's model number and serial number on hand when you call.

Do you have everything pluged in?
did you get a new board or repaired board. I think it's defective if everything checks out

Yes I think the IC's on the convergence board are bad. This board is no longer available from Samsung but is available for repair or a swap from http://www.ptscorp.com. Find the telephone number and call them. or you could replace the two ic's on the board. Good Luck

concergence ics are probly bad mitsubishi had different codes for each module to go into service mode.