Question about Sanyo DP32746 32 in. LCD Television

1 Answer

HD TV not passing the tests offered on network tv

I have a Sanyo HD intergrated TV (about 3 yr old) and thought I was all set when everything changes over in Feb of 09. Our HD TV failed the test that was offered on network recently. What can I do to resolve this problem?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Which network? Cable? Satellite? Dish or Direct?
With any of these providers, you should get an ATSC or "digital" signal. If not, the problem would most likely be with the service provider since they are converting the signal for you. The only way that your set would be affected is if you have an "off air" (antenna) signal only. At this point you would need a converter box. If your service provider is providing you with a HD receiver, then you should have no problem recieving HD (as long as your paying for HD). However, keep in mind, digital is NOT HD. If there is an incompatability with your receiver, check with your service provider for a software or hardware upgrade. Also, check with your local TV serviceman to find out if there are any software upgrades (firmware) for your TV. Being three or so years old, it is possible.
One last thing to check is to see what type of signal you are passing from your providers box to your TV (which type of cable". At a minimum, you need a "component" connection to pass HD content. A "composite" signal is standard definition. Best you can get right now is an HDMI cable. Best "one cable" source for video and audio.
Good Luck.
Tim
Certified TV

Posted on Jan 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a c125 code on my sanyo vizon CLT 1554 that came up when their was an outage with Cablevision 4 days ago.


Sanyo 42 plasma DP42746 just died ' Techlore

www.techlore.com/forum/thread/.../sanyo-42-plasma-dp42746-just-died

Dec 13, 2007 - 27 posts - ‎19 authors
I have a 1 year 9 month old Sanyo DP42746 42" plasma TV. It has been working ... I found that there is an error code on the power supply flashing a d12v error. .... I just took apart my father-in-law's Sanyo DP42746. They've ...Missing: c125

I have a Sanyo DP42746. I am getting an error code (blinking

www.justanswer.com > TV
... (blinking - RL. Find the answer to this and other TV questions on JustAnswer. ... I am getting an error code (blinking 12 times) on the power board. When I .... Question Date Submitted; My 3 yr old 55" Samsung Smart TV will not power on.Missing: c125

Remote Control Codes For Sanyo TVs ' Codes For ...


Nov 29, 2015 | Sanyo Flat Panel Televisions

1 Answer

Could our Dish remote control be causing our picture size problems? The ends of our picture are cut off. We've used the TV remote to change the size but all of those options are still too big.


the ends of the picture on most non hd will be cut off because they are made for the old tvs which don't have the same aspect ratio as the theatre screen shaped flatscreens.

Sep 01, 2015 | Sanyo DP55441 55 in. LCD HDTV

3 Answers

Does anyone know the remote code for a sanyo tv model dp42647 on a dishnetwork remote


Remote Codes ' MyDISH ' DISH Customer Support

https://www.mydish.com/support/remotecodes
Remote Control Manuals · Program Remote to TV/Other .... remote, product type, and manufacturer below to see the current known remote codes you should try.

My Dish remote needs programming for Sanyo TV ... - Directly

https://www.directly.com/.../dish-network-my-dish-remote-needs-progra...
My Dish remote needs programming for Sanyo TV, Model DP226649. My Dish ... Needcode. Alta asked this ... Dish Network • 16808 answers • 95% helpful. Code is ... Test volume control, if it works you're set ... try 590 it should work. tivosat.

How do I program my dish remote to work for my Sanyo TV.

https://www.directly.com/.../dish-network-how-do-i-program-my-dish-re...
Dish Network. How do I program my dish remote to work for my Sanyo TV. ... entercode 590 press pound then sat Then try to turn tv on and off then try volume.

How do you program a dish network remote to my sanyo tv? ' Ya


Jan 09, 2012 | Sanyo 42 in. LCD TV

1 Answer

I have a samsung tv , and im setting up my INTERNET@TV , it ticks off everything but the Gateway Ping ! Please Help


If the Gateway Ping test fails, then your TV is not communicating properly with your Router or Modem.
To resolve this, follow these steps:
  1. Power off your TV, Modem, and Router.
  2. Unplug the power for your Modem and Router.
  3. Make sure the ethernet cable is securely connected to both your TV and your Router or Modem.
  4. Plug in your Modem and turn it on.
  5. Plug in your Router and turn it on.
  6. Make sure your IP Address information entered into the TV during the Network Setup matches the information from your Router or Modem.
  • If you are using an Automatic Setup (most users), skip this step.
  • If you are using a Manual Setup (advanced users), contact your network administrator to determine what the correct IP Address information is.
7. Run the Network Test again.
  • If the Gateway Ping test passes, but another test fails, click here to go back to the list of Network Tests.
  • If all tests pass, the TV is successfully connected to your network.
  • If the Gateway Ping test fails again, see below....
If the Gateway Ping test fails again, there may be a problem with your network setup. To determine if there is a problem with your network, follow these steps:
  1. Power off your TV, Modem, and Router.
  2. Unplug the power for your Modem and Router.
  3. Connect your ethernet cable directly to the TV and Modem.
  4. Plug in your Modem and turn it on.
  5. Power on the TV and run the Network Tests again.
  • If all tests pass successfully, then there is a problem with your Router setup. Contact your network administrator or router manufacturer for information on setting up your network.
  • If all tests do not pass successfully, there may be a problem with the TV. Connect another device (such as a Computer) directly to the modem.
  • If the other device connects to the internet, then the TV will require service. Click the Create online service request button below to have the TV repaired.
  • If the other device does not connect to the internet when directly connected to the modem, then there may be a problem with your modem. Contact your Internet Service Provider for help on troubleshooting your modem.
(from Samsung support)
Hope this helps. -Sa_Les_Ski

Feb 28, 2011 | Flat Panel Televisions

1 Answer

I just switched to an HD receiver. The sound on the HD Channels is lower than the sound on the regular channels. How can I fix this? Dishnetwork has aready checked their end.


Some Sanyo TV's have a feature called Dynamic volume, this feature can be enabled by just pressing the dynamic volume button on the factory remote. We happen to offer a similar feature called volume leveling on our VIP 722k, 612, and 222k receivers. This is a recently released feature that will keep the volume even, during commercials or when changing channels. To access this press menu 6-1-6 and select enable under volume leveling.

Daniel Busa
DISH Network
Customer Service

Oct 03, 2010 | Sanyo DP37647 37 in. LCD TV

1 Answer

Vertical Green Bar 3" wide on the right side of my 42" plasma


My thought is that it is an Intergrated Circuit (IC). But it has been brought to my attention that it may be as simple as adding a "ground adapter" to the plug of the TV. If after you try changing out the ground adapter and it doesn't work, try "power cycling" your TV. (unpluging it... Waiting 30 seconds, then plug it back in.) If that fails, contact Hitachi so they can recommend an authorized service center in your area. Hope this helps. Good luck, KMarshall!

May 25, 2009 | Hitachi 42HDS69 42 in. Plasma Television

1 Answer

42" Sanyo HDTV with 3 HDMI Inputs


Everybody is having problems with sony products and HDMI cables. It's on a lot of forums. So, your not alone.
Most of the solutions are:
1. Unplug your TV for 30 mins.
2. Plug TV back in and put it on HDMI for PS3.
3. Hold down the power button for 10secs on the PS3
That should solve the problem.

Feb 17, 2009 | Sanyo DP42746 42 in. Plasma Television

1 Answer

SANYO 32


Your problem lies in the Power supply. I am an authorized tech for Sanyo, and in the Chattanooga TN area. Contact Sanyo at 1-800-877-5036. At the prompt hit the 0 key, and then ask for customer service. They will be more then happy to assist. If your set is to old for warranty repair you can purchase PWB's at www.shopjimmy.com, they sell used functional circuits at a fraction of the cost.

Jun 15, 2008 | Sanyo DP32746 32 in. LCD Television

1 Answer

HD reception


To have HD on cable, you will need an HD cable box with the HD service activated by the cable company. Some cable carriers will provide some basic HD services included in the base cost with the box.

From the HD cable box to the TV, you will need an HDMI cable between the cable box and the TV set. This is an HDTV interconnect wire. You will have to refer to the instructions on the cable box and on the TV to get everything going properly.

Jerry G.

Apr 28, 2008 | Sanyo DP26746 26 in. LCD Television

Not finding what you are looking for?
Sanyo DP32746 32 in. LCD Television Logo

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sanyo Flat Panel Televisions Experts

The Knight
The Knight

Level 3 Expert

68223 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Cindy Wells

Level 3 Expert

4755 Answers

Are you a Sanyo Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...