Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

F21 error code

We know what the F21 error code is...we have taken the pump apart and cleaned it out but the little white "wheel" was broken off so it wasn't working right. My husband tried to JB weld it back together and after it dried and he put it all back together and ran a test cycle it seemed to be fixed. I went to run a load of laundry today and the noise was back and the F21 error code. We are assuming that piece broke off again. Just curious if anyone has had this problem or knows if you can just replace that white "wheel" or if it's neccessary to replace the whole pump????

Posted by on

  • ams_200412 Jan 22, 2009

    So, you worked at Sears so you are telling me I can go to my local Sears and purchase a pump for this washer for $40 or less. We have called a couple of places that are stating that it is going to cost $85 for a new pump. It is a HUGE flaw and inconvenience! I mean the thing is barely 2 years old...Frustrating! Thanks for the info though!!!

  • ams_200412 Jan 22, 2009

    Thank you very much for the help! I appreciate your reply and help!

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 101 Answers

You will want to just replace the whole pump. It only costs around 40 dollars to replace the pump, maybe less. They don't really sell parts to repair a pump, they just sell the pumps. I used to work for Sears as a repair man and saw this problem all the time. Just make sure to always run your hand through that door boot between washes to make sure nothing is in there. Also make sure there is nothing in any pockets before washing because if there is it will make it to the pump and do it all over again. It's a pain and a flaw that they need to fix on these machines. Let me know if you have any other questions and let me know if this was helpful for you. Good luck and I am glad I could help.

Posted on Jan 22, 2009

  • Dan Harris
    Dan Harris Jan 22, 2009

    As far as I know Sears doesn't sell pumps. I worked at Sears as a Home Repair tech. I sold the pumps off my truck and the price was around 40-50 dollars. Trust me, I know it's a huge inconvenience, the manufacturers need to fix this problem. I wish there was something else I could tell you to do, but I know for a fact that all you can do is replace the pump. I am sorry. Good luck though. If I can be of any other assistance to you let me know.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a maytag 5000 series washer. We are getting an f21 error code. I unscrewed the white drain filter and cleared it. There was little in it. I keep getting the f21 error though. Can you help?


Search Results

    whirpool f21 error code - YouTube

    ? 3:04
    https://www.youtube.com/watch?v=b24PVv-ORqg
    Jul 1, 2012 - Uploaded by davidmontabon
    whirpool f21 error code. ... Maytag , Whirlpool Washer Repair - Drain pump error, no drain - F9E1- MHWE201YW00 - Duration: 4:29.

    My maytag 5000 series steam washer stopped and said Sud ...

    www.fixya.com/support/t8682656-maytag_5000_series_steam
    Mar 17, 2011 - my maytag 5000 series steam washer stopped and said Sud and now says ... Clicking this will make more experts see the question and we will .... I bought aMaytag 3000 seris in 2008 and I am getting these messages: F21 ... Maytag 5000 Series washer F21 error code was flashing and door will not open.

    Whirlpool/Kenmore/Maytag & more-F02/F21 & Sd error codes

    fixedappliance.blogspot.com/.../whirlpoolkenmoremaytag-more-f02f21-...

Feb 09, 2016 | Maytag Washing Machines

1 Answer

I keep getting error code F21 on my kenmore elite which is a drain error the drain is not clogged and the drain hose is not clogged any ideas on what I could do?


The error code F21 is similar to F02 which both pertains to a draining problem. The usual cause is a blocked drain filter or a clogged/kinked. But since those areas are found to be not the source of the problem, the problem must be somewhere else. It is either the drain pump is broken particularly the impeller if the pump just hums/whirs or the pressure switch contacts are stuck/welded together and is, therefore, not tripping. The link below provides the detailed troubleshooting instructions the problem of this kind after the drain filter has been cleaned out.

Error Code F02/F21 on Whirlpool Duet and Kenmore Elite Front Load Washers (Filter Cleaned)

Aug 21, 2011 | Kenmore Washing Machines

1 Answer

I have a Kenmore HE2Plus - it is 6 years old. All of a sudden two days ago I got up to a load of laundry not done, full of water and the code F21. We have gone through most all of your suggestions. At...


The Sd code appears when sud is detected but it may also indicate draining problem such as blocked drain filter or broken drain pump as signified by the long drain error code F21. The drain pump impeller may be broken or restricted resulting in poor draining or no draining at all or the drain pump motor is faulty. Since the drain hose and filter have been cleaned but the error code still persists, the drain pump likely needs to be replaced. Click on the link below for the detailed troubleshooting instructions.

Troubleshooting Error Code F02/F21 on Kenmore Elite and Whirlpool Duet Front Load Washing

Jun 18, 2011 | Washing Machines

2 Answers

What is the F21 code and how do I fix it


its a very common fault but there is a lot of frustration around its fix the fault is a block causing your pump to not work correctly the whole pump pipe lines and so on need to be taken off the filters need to be cleaned to perfection the pump must be taken apart and cleared of any small parts that could have pumped into it. then when your sure there are no blocks filters all clean re assemble the unit re connect the hoses and plug the washer back in and it will work fine.


sonic boom electronics australia.

Jan 06, 2011 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Kenmore Washer 110.4512600, what does code F21 mean? ( 5d?)


If this is a Kenmore Elite front loader series washer, "F21" is a Long Drain error code. This may be an indication that you have an obstruction somewhere in the drainage system. Most commonly, this means there is something lodged in the drain pump or inlet line running from the wash tub to the pump. There is a white screw off cap on the drain pump that you can remove to inspect the pump impeller and clean. The following link explains:

http://www.fixya.com/support/r3608588-f21_error_code

Included is a follow-on link that explains how to check the drain pump to clean. You may also have to remove the inlet hose that runs from the bottom of the wash tub to the inlet side of the drain pump. Debris and small articles of clothing such as socks or under garments can commonly clog in this area as well causing the drain cycle to fail.

NOTE: A "SUD" error code can often occur in conjunction with the "F21" error code. This is due to air being detected in the drainage system, which can occur if the pump is not running, or if you have an obstruction BEFORE the pump. You need to remove the inlet hose from the pump to ensure it is also not blocked. Correct your drainage system fault, and the SUD error (if displayed) should go away.

NOTE: If these preliminary measures do not correct your problem, you may have to replace the drain pump. It does not take much to damage the pump impeller or motor. Since the error code is generated if the drain cycle exceeds 8 minutes, if the pump is damaged and can't pump at the required volume, the error code will continue to appear until the pump is replaced. If the pump requires replacement, the following link explains how:

http://www.fixya.com/support/r3574350-replacing_the_drain_pump_in_a_front_load

If you have any questions about this repair, or need additional assistance, please let me know. I hope this helps you.

Feb 11, 2010 | Kenmore Washing Machines

1 Answer

Code F21


"F21" is a Long Drain error code. This is an indication that you have an obstruction somewhere in the drainage system. Most commonly, this means there is something lodged in the drain pump or inlet line running from the wash tub to the pump. There is a white screw off cap on the drain pump that you can remove to inspect the pump impeller and clean. The following link explains:

http://www.fixya.com/support/r3608588-f21_error_code

Included is a follow-on link that explains how to check the drain pump to clean. You may also have to remove the inlet hose that runs from the bottom of the wash tub to the inlet side of the drain pump. Debris and small articles of clothing such as socks or under garments can commonly clog in this area as well causing the drain cycle to fail.

NOTE: The "SUD" error code can often occur in conjunction with the "F21" error code. This is due to air being detected in the drainage system, which can occur if the pump is not running, or if you have an obstruction BEFORE the pump. You need to remove the inlet hose from the pump to ensure it is also not blocked. Correct your drainage system fault, and the SUD error should go away.

NOTE: If these preliminary measures do not correct your problem, you may have to replace the drain pump. It does not take much to damage the pump impeller or motor. Since the error code is generated if the drain cycle exceeds 8 minutes, if the pump is damaged and can't pump at the required volume, the error code will continue to appear until the pump is replaced. If the pump requires replacement, the following link explains how:

http://www.fixya.com/support/r3574350-replacing_the_drain_pump_in_a_front_load

If you have any questions about this repair, or need additional assistance, please let me know. I hope this helps you.

Dec 27, 2009 | Whirlpool Duet GHW9150P Front Load Washer

6 Answers

Problem with F21 code on whirlpool duet sport


i had the same problem. take the bottom cover off of the front of the washer. on the right you will see a round white screw off cover, it is very tight, it unscrews counter clock-wise. pull this out and see if there is any debris in it. if you look into the hole on the right side there is a hole about 1 inch round, this is the pump opening. you may have to take the gray drain hose off of the back of the pump housing and feel if anything is stuck in there, in my case there was a penny stuck side ways blocking the flow of water. after i took it out the washer has been running great again. this is obviously a design flaw, that something that large could manage to get that far, lucky for me it didn't damage the pump impeller. hope this helps. this should take care of the SD and the F21 error codes.

Aug 04, 2009 | Whirlpool Duet 3.8 cu. ft. Front Load...

1 Answer

Error code F21 - thanks for your help


The F21 error code is an indication that the unit has too long of a drain out condition. If the control calls for the unit to drain & the water does not drain out in 8 minutes or less the unit will stop & flash the F21 error code. I would recommend checking the drain pump & pressure switch circuit.

Clear pump of debris. Tilt machine. Take off front panel. Unscrew large white drain plug. Remove debris.

Unplug from power source...remove front lower panel (3 sheet metal screw wirh 1/4" drive head located on the lower lop of the panel)...open pump strainer (looks like a large stove knob, Turn it counter clokwise, lookout! lots of water will gush out... back flush the pump by filling the outet of the drain hose ( this may dislodge debris that may jam your pump)...re-assemble, plug to power, and turn-on. That will help get rid off the debris.

It can be done if you are patient and able to figure out how the plastic thing comes apart. Good luck!

May 09, 2009 | Washing Machines

1 Answer

F21 error code on a Kenmore HE2 front load washer


Unscrew the pump, there is probably objects in the pump, I get that error every month or so, I find coins in my pump all the time, if too much stuff gets in there the code F21 or sometimes SD comes up.

Jul 24, 2008 | Washing Machines

4 Answers

Oasis washer


F51 error code is beacause the computer board did not receive input from the motor on the bottom. Unplug the washer, pull the machine forward and tilt the machine back. On the bottom you will see a large white wheel with a silver allen screw in the middle I think it is a 6mm allen wrech that takes it off. Once you remove the screw and drop the white wheel, there will be a large coil of wires with 4 5/16 screws holding it on, remove these scres and drop the coils. On the right hand side you will see a connector with three wires , unplug it. Use sand paper or a scraping tool to clean all 3 male sides of the connectors. Reverse process to re-assemble.

Jun 02, 2008 | Kenmore Oasis HE 27082 Top Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...