Question about Alpine CDM-7833

1 Answer

How do you program channel and set time on clock?

I have a Alpine cdm-7833 in a vehicle i just bought (no owners manual).
can you please tell me how to program channels and set time on clock.

thank you
Bob

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,197 Answers

2001 - 2002 Models:

Press the "CLK" (clock) button until the time is displayed, then press and hold the "CLK" button for at least 3 seconds until the time indicator blinks.
While the time is blinking. turn the rotary encoder to increase or decrease the minutes.
Once you've set the clock it will automatically return to normal operation after 5 seconds.
Pre 2000 Models:

Press and hold the "CLOCK" button for 3 seconds until the time indicator blinks.
Press "PRESET 5" to adjust the hour setting.
Press "PRESET 6" to adjust the minutes.
Press "CLOCK" again to exit clock adjustment mode

Hope this helps.

And to set the stations get the station you want and hold down one of the buttons from 1-6 to progream the station. you need to hold the button for about 5 sec.

Posted on Jan 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just bought a car with this stereo. Was working fine and then I accidentally was messing around trying to figure things out and put it in demo mode. Now it's stuck!! Can someone please help?!?!


With the stereo on, hold the large round button in to get to setting menu. When it gets to that, I believe clock adjust comes up first, just turn the knob to get to demo mode and then push the button in. Turn the knob to switch demo off and then push it again. That should do it.

Jan 10, 2017 | Car Audio & Video

1 Answer

With the Uniden UH7700NB How do I tell which is positive and negative on the power input THANK YOU


You can connect the radio to any standard 12 volt DC power source, with either a positive or negative ground. If you don't know whether your power supply uses a positive or negative ground, consult the manual for your power supply or contact the manufacturer.

Jan 10, 2017 | Car Audio & Video

2 Answers

My battery died and I had to get a new battery. I can not remember the security code for the car radio KDC-MP342u can you help?


You may have to contact the manufacturer for details on that. Check in your owners manual for the phone number of their customer service. I had a similar problem after changing battery but found the answer right in the manual. Mine was a Kia.

Jan 07, 2017 | Kenwood Car Audio & Video

1 Answer

Need manual for DVR788-BLK please look into it


http://lastmanuals.com/manual/LG/DVR-788
Find it above for a DVR 788
this is a help site we point you in a direction for a solution for the question. As asked

Jan 04, 2017 | Car Audio & Video

1 Answer

I have a boss 400w riot 2-4 channels,how do i connect the high level wires? Because stereo doesn't have rca's


to use the high level leads, you have to isolate the wires going to each speaker (if using 4 channel mode) or isolate the wires going just to the rear if you are using 2 channel mode. you have to strip a small piece of the insulation off each speaker wire, and run it into the amps high level input harness. if you dont have the high level input harness, you can get a 2 channel high level to rca adapter for around $20. basically, you are tapping into the signal to the stock speakers to feed music to the amp. make sure you get all your positives and negatives correct. brighter wires are usually positive; however you may be faced with sa speaker which uses a grey wire, and another grey wire- the second with a black line. you will have to, again, turn to internet research to determine which is positive and negative, if the colors are not obvious.

Dec 30, 2016 | Boss Car Audio & Video

2 Answers

I am not getting a bluetooth signal from my car stereo. Can this be fixed?


Does specification of your cr stereo say it has bluetooth? If it says, does it has a switch-on function? Look at manual, in setting! Once bluetooth is on, it should start sync with other device, headphone ir speaker, presume

Apr 12, 2015 | Car Audio & Video

1 Answer

My 2002 mazda mvp ausio system is not working but I can insert and eject the CD but cannot do the in tape cassette also the display is not showing the clock or any thing plz any one tell me whats wrong...


Internal board damage. Also the ribbon cable for the soft load on the cassette is not engaging. This can happen due to just ware from the age of the unit. Cold solder joints are usually the culprit, that is why the display will not light. Check yards for a newer used deck it just might be easier unless you have a shop you can send it to.

Nov 10, 2014 | Car Audio & Video

1 Answer

How to reset eclipse avn51d?


www.eclipse-web.com/us

Jul 13, 2014 | Car Audio & Video

1 Answer

How unlock anti theft stock deck


You should have a look at the owners manual, where the code almost sure is... Or maybe a card from the radio.
It will help if you put the car and radio model...

Mar 22, 2013 | Car Audio & Video

2 Answers

How to set clock in 2000 GMC JIMMY


Owners manual: 3-10:

Setting the Clock for Systems with HR and
MN Buttons
Press and hold HR until the correct hour appears on the
display. Press and hold MN until the correct minute
appears on the display. To display the clock with the
ignition off, press RECALL or HR/MN and the time
will be displayed for a few seconds. There is an initial
two-second delay before the clock goes into the
time-set mode.

Setting the Clock for Systems with
SET Button
Press SET. Within five seconds, press and hold the
SEEK right arrow until the correct minute appears on
the display. Press and hold the SEEK left arrow until the
correct hour appears on the display.

Nov 13, 2009 | Car Audio & Video

Not finding what you are looking for?
Alpine CDM-7833 Logo

Related Topics:

632 people viewed this question

Ask a Question

Usually answered in minutes!

Top Alpine Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4748 Answers

Tygh Duval
Tygh Duval

Level 2 Expert

290 Answers

Jaime Hernandez

Level 3 Expert

2272 Answers

Are you an Alpine Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...