Question about CDA Washing Machines

Open Question

WHAT DOES C03 MEAN ON MY CI33IN CDA WASHING MACHINE

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: Washing Machine CDA CI392 Model Manual needed

if you goto www.cda.eu you can download 1 from their

Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Cda washing machine is showing f02 fault code


CDA WASHING MACHINE CI931IN SHOWS FAULT F02 ..not sure if this is your model..when you go to this page just scroll down the page and you will see what you need to read.do not fill any thing in.

Nov 20, 2016 | CDA Washing Machines

1 Answer

Cda 497/1 not washing


see this possible causes: Water-heating cycle the cicles compren washing, and rinse, the machine stop, because the heating element, and thermostat can be defective test.see the diagram Timer test the timer see the diagram for defective, clean contact, with special spray, tigh the wires very well. 5_9_2012_10_57_35_am.gif5_9_2012_10_57_57_am.gif

May 08, 2012 | Dishwashers

1 Answer

What does code f07 mean?


Hi from retired Englishman in SW France,

'F07' for CDA (Whirlpool) washers decodes as ' triac short circuit detection (motor control module)'.
Sorry but this looks like a case for repair/engineer call ;-0(

If this has assisted and/or clarified the situation for you please consider a 4 thumbs up on our rating.
Thanks and good luck!
John C

May 02, 2011 | CDA Washing Machines

1 Answer

I have a konica minolta bizhub c 203 and it give the code c03 ss i don't know what does it mean and i don't know what to do any help


HI i dont think you have the correct error code normally you will have three numbers after the c or c followed by another letter and numbers the only thing i can think of is the suction fan motor this is a c0301 error sorry i can not be more help but your code c03 is not the full code
If this helps great if not please get back to me i would need to know what is the issue with the machine ect can you make a copy or if the code just stays on the machine
I would make sure before doing anything that you have the latest firmware loaded on the machine
hope the above information helps you

Mar 09, 2011 | Konica Minolta Bizhub c203 Copier

1 Answer

My c1392 cda washing machine, firstly stopped spinning and then smoke appeared?


oow, that sounds like the motor has just poped its clogs you may find that fitting a new motor is hardly worth it,,,sorry

Jan 17, 2010 | CDA CI392 Front Load Washer

1 Answer

We have a CDA C1360 Class A washing machine. After a washing cycle the screen has gone off without any power. I have changed the plug and tried different plug sockets and still no power.


Get a different make of machine, we purchased ours as part of a fitted kitchen, chosen for the capacity but it cannot cope with anything near the weight it specifies. More than a couple of jumpers or jeans and it cannot spin, very laboured and so noisy that you have to shout to have a conversation if within 8 feet of it. And now to top it all the pipe you can see inside the drum that the water comes out of is not working it sounds like the motor that controls the circulation of the water is packing up, not a cheap machine and far worse than the previous 2 machines I have owned, if only I had kept hold of my old Zannussi it was head and shoulders above this heap of junk. I will never buy another CDA product.

Jan 11, 2010 | CDA Washing Machines

2 Answers

CDA BI 1200 WD


It could well be the brushes on the motor, take them off and check them (ensure spring still intact and both are making good contact), put them back in, if it begins to work then it'll be the brushes not contacting porperly.

Oct 23, 2007 | CDA CI392 Front Load Washer

2 Answers

CDA C/392


you should e-mail service@cda.eu or contact them through their site; http://www.cda-europe.com/docs/CCD_Home.htm Hope this helps :)

Jun 25, 2007 | CDA CI392 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top CDA Washing Machines Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

noel
noel

Level 3 Expert

4740 Answers

ray gallant

Level 3 Expert

41467 Answers

Are you a CDA Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...