WHEN I POWER THIS MACHINE AFTER INITIALIZATION IT SHOWS MISSFEED ERROR AT BACK DOOR YET THERE IS NO PAPER
IN THE MACHINE , IHAVE CHECKED ALLTHE PAPER TRASPORT WAY BUT ICANNOT SEE ANY OBSTACLE. PLEASE ASSIST.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
First what model? Second miss feed and jam are different, miss feed the roller can grab the paper, replace the roller putting a rubber sleave is going to mess with the feed system. Clean the rollers with alcohol
Here are all the error codes and what you should do:
Codes E1: Water
Supply Error -Display
Shows 'E1' -Water
Supply Error occurs when water level frequency does not show changes more than
100Hz or water is not supplied up to the water level presetting for 20 minutes
or more at the time of initial water supply. -To
help fix this problem please check the Hot and Cold water intakes, there is
a filter screen in each input valve, remove and clean these filters. **
Make sure you replace the filters, they are very important for the operation
of the Washing Machine.** -The
error status can be cleared by turning POWER S/W OFF and resuming the POWER
ON initial status. E2: Water
Drain Error - Display
shows E2 -
case the water level frequency is 25.5Hz or less in the initial phase of UNB-detecting
cycle. - Water
Drain error can be cleared by turning POWER S/W OFF and resuming the POWER ON
status. E3: Over-Flow
Error - Display
shows E3 - Over-Flow
error occurs when the water level is too high. It can be
cleared by turning POWER S/W OFF, turn POWER S/W ON and then run the drain cycle
for 2 minutes. Water is drained prior to POWER S/W
OFF and it is forced to be drained for 2 min if a frequency of more than 25.24
KHz is detected Door Open Error: - Display
shows door - This
can fixed by closing the door E4: Unbalance
Error - Display
shows E4 - Laundry
load is unbalanced; loosen any tangled laundry. - If
only one item of clothing needs washing, the final spin result might be unsatisfactory
and an E4 error message will be shown in the display window. - Unbalanced
error is cleared by POWER S/W OFF and by resuming the POWER ON initial status E6:
Please see "Eb" at end of
list. E7: Pressure
S/W Error - Display
shows E7 E9: Water
Leakage Error EA: Tacho
Error - Display
shows EA - This
is error can be cleared by turning the power off and then on again. Eb: Motor
Triac Short Error - Display
shows Eb - This
is error can be cleared by turning the power off and then on again. E6-EB
only be corrected through Service. Please contact Customer
Service Department at 1-800-SAMSUNG (option 1-1-2) to schedule an on-site service
call for english service.
Thank you for using FixYa. Have a nice day and please remember to rate this solution as if it helps you.
check the registration knob which you can turn by opening the front door and it is located on the right bottom. and also open the right cover to see do the paper comes out as you turn the know from the front, towards left...
1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time. 2. Menu window will show "OKI USER" 3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button. 4. "Diagnostic Mode xx.xx.xx S-Mode is indicated. 5. Scroll to "NV-Ram initial" is indicated. Push ENTER. 6. Window shows "NV-Ram- Initial Table 1". 7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window. 8. Restart printer.
This error code has to do with your finisher. The auxillary tray is not finding its home position or does not leave the home position within the alotted time. Check for binds. I have limited exposure to the K4/3 finisher but try this. Turn the copier off, and open one of the finisher doors. Now turn the copier back on with the finisher door open so it cannot initialize. Once the copier is basically ready except the finisher door is open, close the finisher door and observe all the **** (and theres alot) initialize. This may help determine the problem. I hope this helps...........................SPINAL
paper jam or missfeed always due tothe following:- 1-malefunction of paper feeding system due to broken gears belt chain please check smoth mechnical movement and apply light grease in gears and change any broken part. 2-something is blocking the paper path (staplers-pins)droped inside. 3-malefunction of paper detection micoswitch please confirm free operation for the lever in mechnical one and clean of dust and dirt from optical one,