Question about Toshiba E-studio 281c Copier

Open Question

Toshiba 281c stuck on network initializing

My toshiba 281c is stuck on network initiazing and warm up? Any ideas why? or what to do?

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chad7houston
  • 62 Answers

SOURCE: Toshiba studio 281C problems

You should be able to print on both, but I wouldn't advise it at all. The envelopes are going to jam a LOT and you WILL eventualy get a label stuck inside the machine. Possible....yes. But I don't recommend it. :)
C

Posted on Oct 07, 2008

SOURCE: Toshiba 281C Bypass tray

Problem isn't "solved", but have realized that the issue is related to the fact that the document I am trying to print is formatted for envelopes. When I print a regular word document (letter) it prints fine to the Bypass tray. It must have something to do with the fact that the document is 1000 envelopes. If I print to a PDF file, then print the document to the Bypass Tray I don't seem to have a problem.

Posted on Feb 18, 2009

wheatlandsvc
  • 1110 Answers

SOURCE: Hi, I've have a Toshiba eStudio

Your Hard Disk Drive has failed. Toshiba Digital Copiers do this exact thing when the drive fails as the operating software for the copier is contained on the drive. Look at it as being similar to a computer which will not fully boot up when turned on if there is no hard drive available with an operating system on it. Good news is that the drive is a standard computer drive so they are cheap to buy. The bad news is you will need a trained Toshiba technician to install and then load the firmware onto the hard drive before the machine will run again. I have got machines like this to at least warm up and make copies by "bumping" the machine constantly after turning them on until they boot up. This works on a few of them because you are eccentially bumping the drive into starting to spin up. Once they spin up they will at least come to ready.
Good Luck and Thank You for using Fixya.
WheatlandServices

Posted on Dec 20, 2010

  • 29 Answers

SOURCE: network initializing message for Toshiba

This is normal each do you turn on the copier for 1 until 5 minutes, next to this time do you have firmware problem.
Do you have a nice day

Posted on Mar 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I join a Toshiba 281c to a home group network?


It can be worked with a desktop pc having windows 7 straightly configured to 281c and if the device is shared. Then u can access the desktop pc and browse 281c and send prints. Better to start with as a simple peer to peer connection use TCP/IP and observe that it can be accessed via Internet browser, If the copier utility page appear alright that means ur connected. Good Luck!!

Feb 22, 2015 | Toshiba E-studio 281c Copier

1 Answer

How do i check the ink/toner levels of Toshiba Studio 281c Printer/Copier


You will need the official software from the toshiba support site install it and it will show you toner levels

Jan 23, 2015 | Toshiba E-studio 281c Copier

1 Answer

How do I check Ink/Toner levels on Toshiba e-Studio 281c


You will need the official software from the toshiba support site install it and it will show you toner levels

Jan 23, 2015 | Toshiba E-studio 281c Copier

1 Answer

Toshiba estudio 281c prints faint dow one side but rest of page ok. any helpful ideas to try?????


I would start by posting this in the printer section and not the vacuum section

Jan 26, 2014 | Toshiba E-studio 281c Copier

1 Answer

Replace heater lamp toshiba 281c


open side cover remove fuser kit and replace heat roll OR heat lamp

Nov 24, 2012 | Toshiba E-studio 281c Copier

1 Answer

I have a Toshiba 281c and a few days ago the display started acting up. Now when you power up the machine the display lights up but has no text or menus on it. You can't change the functions it is stuck on...


Hello,
try to enter service mode by pressing 08+power on
enter code 1501 you will see 2 sighns "+" on display
by using plastic stick you can calibrate your display
just touch this "+" jently
then wait few seconds till calibrating process
...
Good luck!!!

Mar 13, 2011 | Toshiba E-studio 281c Copier

1 Answer

Network initializing message for Toshiba e-studio 281C


This is normal each do you turn on the copier for 1 until 5 minutes, next to this time do you have firmware problem.
Do you have a nice day

Nov 16, 2010 | Toshiba e-Studio 350 Copier

1 Answer

Toshiba studio 281C problems


You should be able to print on both, but I wouldn't advise it at all. The envelopes are going to jam a LOT and you WILL eventualy get a label stuck inside the machine. Possible....yes. But I don't recommend it. :)
C

Jun 02, 2008 | Toshiba Estudio 200L Copier

Not finding what you are looking for?
Toshiba E-studio 281c Copier Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Office Equipment & Supplies Experts

didi2005

Level 3 Expert

628 Answers

Branko Djurdjevic
Branko Djurdjevic

Level 2 Expert

102 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Are you a Toshiba Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...