Question about Drills

1 Answer

Milwaukee1/2 magnum hammer drill keyless chuck stuck closed

The keyless chuck has always been hard to open and close now it's frozen shut on a bit. can it be replaced with a keyed chuck?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 142 Answers

Yes call 1-800-sawdust that's the Milwaukee factory number. They can tell you what the spindle and thread sizes are so you can order a keyed chuck. They should even be able to tell you what chuck they have that will fit it.

Posted on Jan 13, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 313 Answers

SOURCE: drill chuck swap

1. Turn the screw clockwise to take it out.
2. Then you needs 3/8 allen key & insert the short side of the allen key & tighten the chuck.
3. hold the drill at the edge of the table & wack the allen key
counter clockwise & do it again as needed.
4. dewalt keyless chuck will fit but you might add a washer to insure the chuck is not rubbing the clutch collar.
5. putting it back together the other way.

Posted on Jun 02, 2008

comax
  • 154 Answers

SOURCE: Bit stuck in Bosch PS20 keyless chuck

These units have only been out for a short while and most are on warranty. Take it to a Bosch Service center in your area and they will replace the front of the unit. Unfortunatly this is a problem with this type of unit. The bit will deform slightly from the impacting action and lock itself in the chuck.

Posted on Apr 13, 2009

meleemore
  • 19 Answers

SOURCE: Makita Percussion Drill HP2051F keyless chuck release problem

jacobs come out with this all metal keyless chuck(i think thats what you have) and if thats the case, there is no solution for this youll have to replace the hole chuck, being its new, it may be under warrenty

Posted on May 05, 2009

  • 583 Answers

SOURCE: Cordless Drill, Keyless Chuck stuck in full open position.

if chuck is wide open ,look down inside there should be an allen screw or bolt at the bottom of the chuck it should undo anti clocwise and the chuck comes off

Posted on Aug 18, 2009

wireguy212
  • 1627 Answers

SOURCE: I have a Black & Decker 18V cordless drill

Look at the three jaws in the chuck,if on is further out than the others the you need to tap ti back into place with a small punch and a hammer.If this does not work then you need to replace the chuck,remove the screw at the bottom of the chuck[where you put the bit],then you will need to to clamp vise grip on the chuck and with it pointed away from you hit the vise grips with a hammer with a sharp blow downward and it should come off.Hope this helps.

Posted on Jun 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you remove or reset a stuck drill chuck


If it is a reversible drill there is almost certainly a left-handed thread screw or allen bolt through the centre of the chuck into the drill shaft and this must be removed before the chuck can be removed.

If it is a keyed chuck select low gear if there is one, fit the chuck key and then strike it sharply with a hammer to jar the chuck in an anti-clockwise direction. Usually it takes only a couple of blows before the chuck is loosened.

Keyless chucks are more problematic. I hold them in a vice and use the drill in reverse which has proved fairly successful, though sometimes the chuck is only fit for scrap afterwards.

Lots of the keyed chucks can be taken apart for cleaning and lubricating if necessary.

Aug 28, 2016 | Dewalt DC740KA Battery 1500mAh, 12V, Ni-Cd

1 Answer

Drillbit stuck


Can not see what model you have. Is it a keyless chuck or an SDS chuck? With a keyless chuck hold the machine in a vice by the drill bit. now tap the chuck with a hammer or pin punch & hammer. DONOT hit the chuck on the jaws gut on the rim around them. I have had success using this method. If it is an SDS type chuck pull the chuck cap up as far as possible along the bit them if there are any ring springs you will have to try remove them then slide the sleeve up the bit, now you should be able to remove any steel balls. If the bit does not come out now hold bit in vice as before and tap on tool holder.

Mar 02, 2014 | Bosch Drills

1 Answer

Milwaukee Magnum Hammer Drill


If the chuck is completely jammed, you can replace it. If its locked but open, then you can remove the screw holding the chuck with an allen wrench. It's going be be tough because it will be secured with glue, such as loc-tite, and it will also be a left handed screw. So be sure to turn clockwise to unscrew it.

You can buy the part at this website, or at a milwaukee service center:
http://www.ereplacementparts.com/12-chuck-p-140621.html

It's a little pricey, but better than buying a new drill. You should also be able to have a service center put the part on for you, if you don't feel comfortable taking it apart.

Feb 03, 2013 | Milwaukee Electric Tool 5370 - 6 1/2"...

1 Answer

Mybrand new RZ20 keyless chuck will not close around a bit.


If a large enough drill bit is inserted too far so it bottoms in the chuck, the jaws run into the bottomed shank and will not close beyond a certain point due to the interference. If you hold the drill bit out about 1/2 inch from the bottom, the jaws should close on the bit. I assume you have tested the chuck without a bit to verify they can close.

Feb 15, 2012 | Drills

1 Answer

Keyless chuck has bit stuck in it


use some kind of lube like liquid wrench or wd40 and let it set for a bit. Then tap it with anything like a wrench, hammer, etc.

Feb 12, 2012 | Drills

1 Answer

My keyless chuck will not tightten all the way closed....seems to catch on something


Open the chuck and see if the screw inside the chuck has backed out. The screw is left hand thread so you will need to turn it to the left to tighten it. It may be an allen or Torx head screw.

Jul 15, 2011 | Milwaukee 2690-24 18-Volt Hammer-Drill,...

1 Answer

I have a Black & Decker 18V cordless drill with keyless chuck. The spot where the drill bit fits is in the open position stuck and won't turn in either position. What am I missing how to unlock it?


Look at the three jaws in the chuck,if on is further out than the others the you need to tap ti back into place with a small punch and a hammer.If this does not work then you need to replace the chuck,remove the screw at the bottom of the chuck[where you put the bit],then you will need to to clamp vise grip on the chuck and with it pointed away from you hit the vise grips with a hammer with a sharp blow downward and it should come off.Hope this helps.

Jun 12, 2010 | Black & Decker CD9602SB 9.6 Volt Cordless...

1 Answer

Black decker drill keyless chuck won.t open !


hold the back of the chuck with channel locks or a vice and use the same channel locks on the front and open the chuck manually it should work and you can get to the screw to replace it or the hand chuck. this can be a little frustrating but hang in there and you'll be a pro shortly.

Sep 02, 2009 | Makita Usa Inc No.8390DWPE 18V Crdls...

1 Answer

Black and Decker Cordless Drill Chuck stuck in full open position


I'd put penetrating oil in it and tap the chuck with a plastic hammer. That should free it up.

Best rgrds, W/D

Aug 18, 2009 | Black & Decker Drills

3 Answers

Keyless chuck problem


I had the locking screw come loose in the center and bottom of the chuck it has a left hand thread and is a torx head . It had backed out and prevented the chuck from closing.

Mar 14, 2008 | Dewalt 18 Volt Compact Drill Kit

Not finding what you are looking for?
Drills Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Drills Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Brad Brown

Level 3 Expert

15478 Answers

Are you a Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...