Question about Office Equipment & Supplies

1 Answer

How to solve the problem canon ip 3680 ink absorber

Ip3680

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 32,281 Answers

Ink Absorber Full
This may clear the ink absorber problem. There is ink absorbers located at both ends of the printer where the ink head move.
To dry the ink absorber, power up the printer and open the cover so the ink cartridges and print head will move to the middle of the printer.
Then take several sheets of absorbent tissue, fold it into a pad and place it inside the printer over the ink absorber on the far left hand side of the printer to soak up the excess ink. You may need to change the absorbent tissue a few times. Then repeat the same procedure on the right hand ink absorber.
Close the lid and the printer should now function normally.

Posted on Jan 11, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: waste ink absorber full

It's Very Simple

Just Enter in Service Mode of your printer and clean absorbers count.
To enter in SERVICE MODE
1) Power off Printer
2) Push and hold "Resume" button and then push and hold "Power" button
3) Hold the Power button, then release and 2 times press Resume button
4) Led indicators must change
5) Release all buttons
6) Then printer in Service Mode
(If something wrong, repeat 1-6)

To clean absorber counter,
7) Press "Resume" Button 4 Times and after press Power button. It's all! Your absorber count is EMPTY!

In SERVISE MODE you can do several useful things:
To print Service Nozzles test, press "Resume" 1 time and press Power
To print EEPROM data, press Resume 2 times and press Power.

DO NOT press Resume 3 times and POWER. It will reset some EEPROM data settings

Any Question mail me: ossipenko(prettydoggy)gmail.com

Posted on Feb 05, 2009

pineworks
  • 4041 Answers

SOURCE: My canon i950 waste ink absorber is almost full

1. Start with the printer OFF
2. Hold down RESUME and then hold down POWER
3. release RESUME
4. press RESUME twice, then release POWER
5. Let green light blink until printer is done moving print head.
6. Select functions below with RESUME press POWER to execute:

Number of presses - light color - function
0 presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter

Posted on Feb 13, 2010

  • 1 Answer

SOURCE: Canon Pixma ip1300 Ink absorber is full what can i do

another solution for a quick override is to unplug the power lead from the back of the printer. With one hand hold down the power button on the printer whilst simultaneously plugging back in the power lead. When the light is back on, take your finger off the power button. You may need to press the power button once more, but this should 'override' the problem until the next time you turn your printer off.

Posted on Apr 16, 2008

  • 1 Answer

SOURCE: Waste ink absorber on canon iP 1600

For Canon ip1000 and ip1600, maybe others

1. remove cartridges
2. unplug AC power
3. hold power button and plug AC power (keep holding power button.
4. press resume 4 times


The waste ink counter should be reset by now

Or

http://www.servicemanuals.ru/download/canon/ip1600.htm

Posted on Nov 30, 2007

  • 1 Answer

SOURCE: Waste Ink Absorber is full In Canon Pixma IP3300

my printer say, "the ink absorber is full".

Posted on Dec 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Canon printer iP 3680 says ink absorber almost full...what to do


Nothing you can do! Next message will tell you it's full and to take it to a Canon Service Department. But what they really want you to do is buy a new one. It's called built in obsolescence!

Sep 09, 2012 | Acer Office Equipment & Supplies

2 Answers

How to replace ink absorber canon mx310


Hello,

Unfortunately this is not an end user item. The ink absorber is basically a big felt pad. When the printer cleans the print heads at the beginning of the print cycle it spray ink on the pad o clean the printhead nozzles. The printer is programmed to count these cleaning cycles and when the number is up it gives the ink absorber error on the display. The printers use the ink absorber to prevent the used ink from dripping out of the printer onto you table or desk. By the time the absorber registers that it is full it really is soaking wet with ink, you don't want to deal with that mess. It really is like an end of life for the printer notification. You would have to open the printer, remove and wash the absorber and clean the holder then reset the counter in the printer just to get t going again. The manufacturers don't even sell the absorbers because they treat this as a non-repairable printer. Sorry for the news but I have been a printer tech for 15 years and that's really the best thing to do, get a replacement printer.

Jul 19, 2012 | Canon PIXMA MX310 All-In-One Printer

2 Answers

How to fix canon ip 4800 ink absorber


i have a problem with my canon 4800 it say ink absorber is full, how can can solve that

Nov 29, 2011 | Canon PIXMA Office Equipment & Supplies

1 Answer

Canon printer iP 3680 says ink absorber almost full...what to do


Read and follow this
http://pcmediks.blogspot.com/2010/09/canon-ip3680-resetter.html

Feb 14, 2011 | Office Equipment & Supplies

2 Answers

Ink absober is full


Eight flashes: Waste ink absorber almost full

The printer has a built-in waste ink absorber for the ink used during Print Head cleaning. Eight flashes indicates that the waste ink absorber is nearly full. Press the RESUME/CANCEL button to cancel the error so you can continue printing. Before the waste ink absorber becomes completely full, contact a Canon service representative.

Important

Canon recommends that you call for service as soon as this error occurs. Once the waste ink absorber becomes completely full, printing will no longer be possible

Jan 11, 2011 | Casio Office Equipment & Supplies

4 Answers

Canon i9950: Full waste ink absorber


Dhedik maybe this action can solved your problem Reset Waste Ink Counter printer Canon i9950 :  1. power off  Printer 
2. Push and hold resume  button and push power button 
3. Hold  Power button and release Resume  button 
4. Push Resume button twice ( 2x ), and now release resume button and power button 
5. Green light will blinking and  stop.
6. When green light on, push resume button 4 x 
7. Push  Power button and printer will off, if that isn't off, push power butto again until print off position.

ok good try, don't forger to vote me, Fixya  

Apr 02, 2008 | Canon BubbleJet i9950 InkJet Photo Printer

9 Answers

The ink absorber is full for pixma 1880


This is the REAL working method of manually resetting Canon ip1880 - ip 1980.

1. Unplug the POWER cord.
2. Press & hold the power button.
3. Connect the power cord WHILE holding the power button.
4. Keep on holding the power button for about 30 seconds.
5. Release the power button. The printer should be turned off.
6. Turn the printer on and that's it!

NOTE: You have to do this every time you turn on your printer. Or you will get the waste pad full error.

Hope this helps.
vulmec.wordpress.com

Jan 15, 2008 | Office Equipment & Supplies

5 Answers

Question for canon pixma iP 1000


folow these steps to reset it..
Step 1: Manual for Service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.

Nov 02, 2007 | Office Equipment & Supplies

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

979 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

k24674

Level 3 Expert

7993 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...