Question about Bench Grinders

1 Answer

Window media problem unsopported format

I change my first tilt because i had some problem with it.When the warrant send me the replayment of my phone.It did not came with same format support.So that left me on wire.I am tiring to fix my media player 10.3 to have the same format that orginal came with. {I HAVE TCPMP to see my movies BUT I WOULD LOVE TO fix my media player.

Posted by on

  • Thomas F. Schneider May 11, 2010

    Bench grinders have media players now?


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,692 Answers

Just download and reinstall the media player using the Windows add programs  form the windows disk.Or , if available , and I an not sure, download it from the Micro Soft website site reinstall it. 

Posted on Mar 03, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I change a grinding wheel to a Wire wheel on my new grinder # 37823

There is a left handed thread and a right handed thread on the arbors.

Right Hand Side (RH)
Wrap a piece of rubber or leather around the threads on the LH side of the arbor & hold with pliers, while turning the RH nut CCW.

Left Hand Side (LH)
Wrap a piece of rubber or leather around the threads on the RH side of the arbor & hold with pliers, while turning the LH nut CW.

Note: Hand tighten the nut, then 1/4 turn.

Right Hand Side (RH)
Wrap a piece of rubber or leather around the threads on the LH side of the arbor & hold with pliers, while turning the RH nut CW.

Left Hand Side (LH)
Wrap a piece of rubber or leather around the threads on the RH side of the arbor & hold with pliers, while turning the LH nut CWW.

For grinding stones:
  • ring test the stone
  • discard the stone if it has been dropped
  • be sure the paper washers are installed on the wheel

GRINDER SAFETY 101 (graphic injury video so be warned)

Feb 14, 2015 | Bench Grinders

1 Answer

How do you change the wheels on this bench grinder

Once you get them snugged a little, you will probably have to hang onto one wheel while you tighten a nut. It's easier if you tighten down one wheel with the other wheel dismounted so you can really grab the arbor shaft.

Do NOT overtighten either wheel - it doesn't need it, and overtightening increases the risk of a catastrophic wheel explosion.

Apr 28, 2014 | Bench Grinders

1 Answer

Need belt for bench grinder belt #lb-12

To find the correct belt you will need to know the Brand and Model Number. Is the number on your old belt or on the grinder? Once you have the correct info you can get parts list by google searing for that. here is what I got just using the bench grinder belt #lb-12.
Just cut and paste the link in a new browser window.
Hope this helps..

Nov 04, 2012 | Bench Grinders

1 Answer

New shaft for a delta 23-840

You need to check if the cost of the shaft will be too much and whether it makes sense. You have not indicated the reason for changing the shaft, if there is damage e it can be mended in most cases with the help of a machine shop.
So check cost with replacement before you attempt.

Oct 28, 2011 | Delta Bench Grinders

1 Answer

No control of speed on bench grinder,need schematic

Unless the motor is a brush type universal unit, there is commonly no way to change the speed of an induction motor. There are AC motor speed control units available, but cost more than the grinder as they change the frequency as well as the voltage. There are speed controllable grinders available that use brushes so that simple electronics can control speed. Hope this helps!

Dec 08, 2010 | Craftsman 6" Bench Grinder with Lamp

2 Answers

How do I change a brush? I can't get the axle locked to get the nut off. Can you help me?

Remember if you are trying to change the left side it is a reverse thread nut. You would turn it clockwise to loosen. IF it is very tight, put a wrench on both sides. IF the right side comes loose, remove brush/grinding wheel, and re-install nut, with an extra nut locked to the first one, the put a wrench on both sides again.

Sep 30, 2010 | Sears Rockwell 8 in. 3/4 hp, 5-amp Bench...

1 Answer

My Makita bench grinder has four holes to change the grinding to I get the retaining nut off as I don't have a tool to fit the four holes?

Make your own wrench out of a piece of wood stock,with 2 screws or nails spaced out to 2 opposing holes in the retaining ring/nut.HarborFreight sells a 'spanning wrench' online .

Jun 30, 2010 | Makita Nip 5"(127mm) Bench Grinder Wheel...

1 Answer

Bench Grinder blown fuse

try the fuse first then try the red reset button under the base.

Mar 05, 2010 | Clarke Power Products Cast Iron Bench...

1 Answer

How to change the craftsman 6'' grinder wheel?

without having the model number I can only go from experience on other grinders. First you would have to unplug tool and remove outer guard housing to expose the hex nut, one side of the tool would have a left hand thread and the other standard so you would need to hold both the hex nuts at the same tme and try both ways, when you get one off put a GOOD pair of pliers or similar device on the shaft and remove the other wheel

Jul 17, 2009 | Craftsman Bench Grinders

Not finding what you are looking for?
Bench Grinders Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bench Grinders Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Bench Grinder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides