Question about Procom ML300EBC Heater

1 Answer

Runs fine for 2-4 minutes then shuts down.. auto..

I couldn't provide a 3 feet head room it is at 16 inches. It seems like as soon as the internal fan kicks in it shuts down.. Is the thermocupal cooling and then shutting down ?? OR potentially O2 sensor given the high/clearance issue.. I have installed in my garage and would like to keep it higher to eliminate the kid hazard potential issue.. Spoke with an installer and they feel it is the clearance issue.. But, I am hopeing that is not the case.. Thoughts ???

Posted by on

  • ronald_b_kel Jan 23, 2009

    It is brand new.. Pro-com Natural Gas Procom ML300EBC Heater



    I appreciate it...

  • ronald_b_kel Jan 23, 2009

    The flame is not the perfect..... I do get yellow tips 1 or 2, it is not the low consistent blue flame...

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 70 Answers

How old is this heater? does flame stay on thermocouple? what is the make and model # then i can look up some manuals of the heater and maybe give you some thoughts of what is going on. clearance could be a problem but i don't think it is.

Posted on Jan 23, 2009

  • Scott Magill Jan 23, 2009

    how long do you run the heater before you turn on fan? I talked with a procom rep. he said you do need the 36" clearance since it is a vent free. i could not find that model # on there site. I would try to lower the heater and see if that makes a difrence.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to calculate cubic feet ?


Calculating the cubic feet of a space requires multiplying the area of the bottom times the average height. You get the bottom area by multiplying the length times the width. Remember, to get cubic feet, you need all your measurements in feet to start with.

Here is your formula:

VOLUME (in cubic feet) = Length (in feet) X Width (in feet) X Height (in feet)

If it's a rectangular room you're working with, it is all straightforward. If there are irregular walls, it may be necessary to divide up the room into rectangular sections and then add together their individual volumes. If the ceiling is sloped, you need to use the height that has the same ceiling area above it as below it. Good luck! Truly.

Jul 25, 2014 | Building Materials

1 Answer

Trouble with Maytag Legacy gas Dryer


Please provide the model number and I will see if I can figure something out.
It sounds like you have covered the common problems. Usually a motor is the cause for this problem, it gets hot and shuts down until it cools off. I have had some problems with the auto dry controls on the Maytags also.
Are you equiped to do some voltage checks if we need too? This would help in knowing where you have power when it quits.
Thanks/Mike

Dec 12, 2007 | Dryers

1 Answer

Flat panel TV comes on by it's self


It sounds that the voltage output from its internal power regulator board is not proper. Check it.

Feb 04, 2013 | Samsung UN19D4003 TV

1 Answer

What is the recommended size of a room for a ping pong table?


Here is a list of the standard and official ping pong room sizes. I guess that if you're planning a ping pong room in your house, you can use the last in the least as your minimum. But remember, the bigger, the better..

International Events, World Championships & Olympic Games
14m x 7m (46 feet x 23 feet)


National tournaments
12m x 6m (40 feet x 20 feet)

National league / Representative matches
10m x 5m (33 feet x 16 feet 6 inches)

Local league / Local tournaments
9m x 5m (30 feet x 16 feet 6 inches)

Recreational play and coaching
8.5m x 4.12m (28 feet x 13 feet 6 inches)

Jul 09, 2012 | Sport & Outdoor - Others

1 Answer

Flotecpump runs for 5 minustes or less and shuts down due to over


Hello,

With a 1-1/2 inch suction and a 2 inch discharge, you have no backpressure, and it's actually beneficial to have a working head. Try pinching the discharge valve to maintain a steady discharge pressure of at least 20-30 psig on the pump case. Tinker with the discharge pressure as required to balance the pump. As a general rule, the suction line is never smaller than the discharge line to prevent cavitation of the pump. A temporary move of pinching the discharge will compensate some, but it is better to increase the size of the suction line, if the pump will handle it. If the rated pump volume is low, you may also be trying to exceed it's capacity, and heat wil result in the motor.
If at all possible, convert the voltage to 220v as this will also make you more effecient and pull half the amps. Most pumps can be wired either way, and usually the diagram for swapping is included or inside the motor housing. Converting is easy.
Best regards, --W/D--

Aug 25, 2009 | Plumbing

1 Answer

I installed a 2 hp high head pump on a waterfall and the amps are running about 16 when I start closing the discharge side of the pump the amps come down where they are suppose to it is going out on...


make sure your wireing is up to the job and your back presure at the pump discharge is within limits. both of these should be in your pump book that comes with your pump. If you don't have one you should be able to look it up on-line or order one from Pentair.

Aug 15, 2009 | Pentair Challenger High Head 1.5 Hp Pump...

4 Answers

Frigidare window air conditioner with remote control about 3 yrs old. All controls seem to be working except when the energy saver mode is suppose to shut down the unit / the display goes dark but the...


Hello, I can assist you.

If the unit is supposed to turn off and it doesn't, it will be necessary to check several things.


  • First, is the unit cooling properly? See the section entitled "The air is cool but doesn't seem cold enough."

  • Next, is the temperature of the room adequately cool? If the room temperature is cold enough try setting the thermostat to a higher temperature. If the unit then seems to work properly leave the thermostat set to the higher temperature.

  • If the unit is cooling properly when it is turned on and the room is not cool enough the problem is probably that the unit is trying to cool an area that is too large for its capacity. Use the following chart to find the appropriate size air conditioner to use:

AREA TO BE COOLED / CAPACITY (BTU/HR)

100 to 150 square feet = 5,000

150 to 250 square feet = 6,000

250 to 300 square feet = 7,000

300 to 350 square feet = 8,000

350 to 400 square feet = 9,000

400 to 450 square feet = 10,000

450 to 550 square feet = 12,000

550 to 700 square feet = 14,000

700 to 1000 square feet = 18,000

If the room is heavily shaded, reduce needed capacity by 10%

If the room receives a lot of direct sun, increase needed capacity by 10%

Add 600 Btu/Hr for each person in the room if there are more than two people

If the unit is for a kitchen, increase the capacity by 4,000-6,000 Btu/Hr.

If the room size is too big for the air conditioner you have two possible choices. Either decrease the room size by shutting some doors or partitioning off an area of the room. Or, increase the BTU of the air conditioner for that room by installing a different air conditioner with a higher BTU rating.

Aug 02, 2009 | Heating & Cooling

1 Answer

Paslode im250 f-16 only able to drive 2 nails .


Bad Fuel cell!!! New cyliders now have expire date on bottom of cannister. If old will not fire properly. Put new fuel cell in should be fine.

Feb 21, 2009 | RTO Paslode 902000 IM250 Ii Cordless 16...

Not finding what you are looking for?
Procom ML300EBC Heater Logo

Related Topics:

336 people viewed this question

Ask a Question

Usually answered in minutes!

Top Procom Heating & Cooling Experts

paulcarew

Level 3 Expert

2364 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

john h

Level 3 Expert

8286 Answers

Are you a Procom Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...