Question about Panasonic PT-51HX42 51" Rear Projection Television

1 Answer

Panasonic TV projector PT 4743G

I have a Panasonic Projector TV , model PT 4743G. The resistor R7011 was burned. Replaced with a new one (it is a 2.2 Ohm, 2W resistor) and the new one got burned as I powered up the unit. There is a short, looking at the diagram i could not tell if a faulty STK392-110 is the issue or not. Does any one knows something more. I could provide schematics and diagrams of the circuit if you like. Thank you - please write to: vassilis.danginis@smsc.com

Posted by on

  • Billdang Feb 02, 2009

    Thank you very much - I will give a try - Best regards

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Panasonic Master
  • 8,617 Answers

Yes the convergence ics will blow that resistor

Posted on Jan 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Panasonic TYLA1001 Manual Lamp Replacement Instructions Models No. PT-52LCX66 /...


Panasonic TYLA1001 Manual
Lamp Replacement Instructions

Models No. PT-52LCX66 / PT-56LCX66 / PT-61LCX66
Models No. PT-52LCX16 / PT-56LCX16 / PT-61LCX16

9fe2fcd.jpg

Are you missing the Installation Instructions for your Panasonic TYLA1001 Replacement Projector Lamp?

A digital, pdf version of the TYLA1001 Lamp Replacement Instructions can be downloaded from here.

Once installed, reset the lamp timer of your Panasonic Multimedia Projection HDTV by following these steps.

I hope that helps.

on Apr 11, 2010 | Panasonic TYLA1001 TYLA1001 Projector Lamp

1 Answer

I have two Panasonic PT-LB10VU projectors doing the same thing. They project find with RGB, but when trying to project a VHS tape through video, the image rolls or has multiple lines running through it. ...


first of all you replace the present video driver VHS tape and try any other dvd driver or any other video device if problem exist then the main board of you projector is faulty.

Solution: open the upper over remove 5 screw back side of projector.
disconnect the panel ribbon cable.Remove lamp cover with 3 screw remove main board with 4 screw and 8 connector. put it face down on a table and use a table lamp for more light.
check very carefully the area I show in the picture with red arrow there is a resistor no.R041(on resistor 750) is burn out or black replace witch 75ohm resistor and check around the resistor if burn any other component replace with the same after repair of main board fix the all part of projector as you open. Power on and use any video device other than your VHS tape maybe the high voltage comes on video output.
if fault exist then need to be replaced the main board. good_help_11.jpg

Dec 20, 2010 | Panasonic PT-LB10VU Multimedia Projector

1 Answer

Panasonic projector TV PT-43LC14 has a light yellow splotch on the left hand of the screen. Can this be fixed?


yes and no. it is a burn spot on the light filter on the blue lcd panel due to excessive dust and heat. panasonic does not sell individual parts of the optical engine, so you'll have to replace the entire engine. to avoid it happening again or getting worse, keep the projector cool and dust free. use canned air to blow it out.

Nov 30, 2009 | Panasonic PT-AX200 LCD Projector

1 Answer

I need to identify the parameters (rating) of a resistor for a Panasonic PT53WX53G projector big screen tv. It got hot so I can not see the color codes on it. This resistor glows red when TV is turned...


The resistor you see is a 2.2 ohm 2 watt resistor and is part of the convergence circuitry. I would replace R7011. 7012, 7013, 7014, 7015 & 7016 (all the same value) and the 2 STK392-110 Convergence ICs. This should fix your problem. You can find kits on-line for around $45 with the IC's and resistors together.

Nov 26, 2008 | Panasonic PT-53WX53 53" Rear Projection...

1 Answer

Panasonic PT-AE700E HD Projector, Has A Colour Problem


the filter on your projector has gone bad the same needs to be replacerd

Nov 04, 2008 | Panasonic PT-AE700U Multimedia Projector

1 Answer

Replaced 2 resistors one burnt up. please help


They would only burn if your convergence ICs are bad so if you didnt change the ICs with the resistors they will keep burning.

Apr 29, 2008 | Panasonic PT-53TW53 53" Rear Projection...

1 Answer

PT-53TW53 resistors needed


They are 2.2 ohms, 5%, 2 watts.
You can try digikey.com or radio shack.

Apr 11, 2008 | Panasonic PT-53TW53 53" Rear Projection...

1 Answer

Parts for panasonic pt-53tw53g


r7011 = 2.2 ohm 2 w...
r7015 = being researched....
Partstore.com ...........................................T.

Apr 09, 2008 | Panasonic PT-53TW53 53" Rear Projection...

Not finding what you are looking for?
Panasonic PT-51HX42 51" Rear Projection Television Logo

Related Topics:

337 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Televison & Video Experts

 Grubhead
Grubhead

Level 3 Expert

4943 Answers

The Knight
The Knight

Level 3 Expert

73118 Answers

Jaime Hernandez

Level 3 Expert

2307 Answers

Are you a Panasonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...