Question about Sharp AL-1641CS Laser Digital Copier

Open Question

Sharp AR-287 error code c1-00 - Sharp AL-1641CS Laser Digital Copier

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
mickspaceNET
  • 115 Answers

SOURCE: I want a solution for a Sharp AR - 287 Digital Image problem

H4-01 = Sub heater lamp abnormally low
temperature detection

If your fusing unit is old replace the whole Fusing unit.. this will solve jaming issues you might have there as well.. call an authorized service tech if your unsure of what this all means?

Posted on Oct 23, 2008

Ad
  • 12 Answers

SOURCE: Sharp AR-287 error code HR-00

The AR 287 does not have any codes that begin with "HR". Please recheck the display and post again with correct code and I will try and help you.

Posted on Jan 07, 2009

007tech
  • 95 Answers

SOURCE: need to reset key operator code on Sharp AR-287

Make sure the copier is in "copy" mode.
To get into service mode press the following keys one after the other "P" key - "interupt" key - "clear" key - "interupt" key (do not play around with setting in service mode as this can render your copier useless)
enter 22 and press "start" enter "7" and press start. This should display the admin code.
Restart the copier and you should be good to go.

Posted on Mar 26, 2009

007tech
  • 95 Answers

SOURCE: Sharp AR-287 HR-00 error code

I'm sorry for not getting back to you sooner - I lost track of this question. If you still need this info here it is :
H3-00 indicates a temperature problem in the fuser unit. not reaching a certain temperature within a certain time.
It could be a thermostat or thermistor problem - both monitor temperature. you could remove the fuser unit and make sure these items are clean - no build up on them. there should be a center and side thermistor.
You can reset the error code in SIM mode by pressing the following keys one after the other "P" "interupt" "C" "interupt" then 14 and start/copy key. confirm if required. make sure the copier is restarted afterwards.
If the error persists then you may need new thermistors.
Hope this helps.

Posted on Apr 12, 2009

  • 257 Answers

SOURCE: Error Code E7-11 on a

This code is related to laser unit functioning problem. Power the machine off and on and if it appears again, do the following;

  1. Open document glass and clean inside mirrors and document glass with a clean dry soft cloth and test.
  2. Check flat cable that connects copy lamp and attach firmly from the main board.
  3. Replace the laser unit if the above fails.
Ask for assistance if you doubt from a qualified technician and you will succeed.

Posted on Dec 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

SHARP AR-287


Is the code a H5 ? Is it a AR-163 or a AR-287? Is the copier making a load noise when making a copy? Basicly, the code means you are have more then 5 paper jams in the fuser & there is a problem there & the copier is locked up.... It's self saving it self

May 05, 2010 | Sharp AR 163 Copier

1 Answer

Error f2-31 en fotocopiadora sharp ar 287


You must your copier TD cartridge,then solve your problem.If you are not fix it,Then press
C>Photo>C>photo>16> start key

Apr 19, 2010 | Sharp AR 163 Copier

1 Answer

I have sharp ar-287 error ha-04. How to fix?


this sounds like you have a jam in your fuser unit.To remove this jam open the door at the left hand side,you should see a green lever to the back end lift up and take paper out,after doing this you then have to reset this error code.To enter service mode press P interupt C interupt key in 14 press start key then press CA.Photocopier should reboot if this does work then you need to get your service engineer out

Sep 15, 2009 | Sharp AR-507 Copier

2 Answers

I want a solution for a Sharp AR - 287 Digital Image problem


H-4 is an error code for the fixing assemblyand needs to be reset thru a simulation code, sometimes a power flucuation can cause this error and therefore may not need parts.
press #
press *
press clear
press *
when it is done properly the display will go blank
then enter 14
then press the start key, turn the machie off and then back on.
If the code comes back you'll need something for the fixing assembly
Good luck

Bob

Apr 27, 2009 | Sharp Office Equipment & Supplies

1 Answer

Sharp AR-287 HR-00 error code


I'm sorry for not getting back to you sooner - I lost track of this question. If you still need this info here it is :
H3-00 indicates a temperature problem in the fuser unit. not reaching a certain temperature within a certain time.
It could be a thermostat or thermistor problem - both monitor temperature. you could remove the fuser unit and make sure these items are clean - no build up on them. there should be a center and side thermistor.
You can reset the error code in SIM mode by pressing the following keys one after the other "P" "interupt" "C" "interupt" then 14 and start/copy key. confirm if required. make sure the copier is restarted afterwards.
If the error persists then you may need new thermistors.
Hope this helps.

Mar 30, 2009 | Sharp AR 163 Copier

2 Answers

F9-00 (Print Function) Error Code on Sharp AR-287


this copier will display f9-00 if the nework is not connected or the card is bad this means network connection lost usaally resting copier will work if the network is on if not call service

Mar 03, 2009 | Sharp AR-235 Copier

1 Answer

Sharp AR-287 fault code E7-11


Hello sir; The error code means there have communication problem between main board and sub board,operation board, icu board or print, my suggestion, go buy a new copier, it not worthy to repair !

Feb 27, 2009 | Sharp AR-235 Copier

1 Answer

Sharp AR-287 error code HR-00


The AR 287 does not have any codes that begin with "HR". Please recheck the display and post again with correct code and I will try and help you.

Dec 24, 2008 | Sharp AL-1641CS Laser Digital Copier

1 Answer

My Sharp AR-287 Copier is showing F2 error


there Should be 2 additional numbers. F2-??

Oct 29, 2008 | Sharp AR-235 Copier

2 Answers

I want a solution for a Sharp AR - 287 Digital Image problem


H4 for an error code on all Sharps indicates that the fusing temperature isn't correct. It needs to have a new thermistor installed or the heating lamps need to be replaced.

Oct 21, 2008 | Sharp AR-235 Copier

Not finding what you are looking for?
Sharp AL-1641CS Laser Digital Copier Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

Anthony Karuku

Level 2 Expert

257 Answers

jasbo
jasbo

Level 3 Expert

2237 Answers

Adorjani Laszlo

Level 3 Expert

1297 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...