Question about Marantz SR6001

1 Answer

Marantz SR6001 AV Surround Receiver - Blinking Standy Light

Unit just shut off - standby/power light starting blinking rapidly.

Unplugged unit to see if it would reset - to no avail. Standy/power light still blinking rapidly.

Any ideas? yup, first time yesterday... unplug, replug cured it (reset combo buttons didn't work) Today its offline alltogether. Even unplug/5 min not working.

Posted by on

  • gbanksjr Jan 21, 2009

    Funny, i have the same problem - although unplugging the unit does seem to help temporarily but the unit does slip back into protection mode shortly thereafter. Spoke with Marantz who suggests unplugging all the speaker wires and testing them one by one, assuming you can get the unit operable again, which i've tried to no avail. I've read on blogs that others have experienced the same problem with this unit and others like it in the series. When and where did you buy the unit?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have exactly the same problem! Sometimes when I turn the input dial it comes back on but this time it is out for good. I have tried re-wiring and unplugging etc. nothing seems to work.

Posted on Jun 13, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Onkyo ht-rc180 standby light blinks will not start.i tryed factory reset, still blinks


The amp protection circuit has been activated. Remove the power cord from the wall outlet immediately. Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and reconnect an input and a pair of speaker wires onto the unit. If the receiver still does not turn on than you will have to bring it in for service. Turn up the volume and if the receiver doesn't shut down, power off the receiver and add another pair of speakers. Power up the unit again and turn up the volume. If it doesn't shut down, power off the unit again. Now connect all your input sources and turn on your receiver. If the unit shuts down again, your unit will need to be further serviced at an authorized Onkyo service center.

Sep 24, 2014 | Onkyo Ht-Rc180 7.2-Channel A/V Surround...

1 Answer

Standby light is flashing rapidly and I cannot turn on


Register and download the manual for free at retrevo.com

http://www.retrevo.com/support/Marantz-SR7002-Receivers-manual/id/6753ci475/t/2/

Page 81...


PROTECTIVE FEATURE


In some cases, the STANDBY indicator may blink slowly, twice per second. In this case, turn off the unit, unplug the power cord, and check the following points.


Make sure the speaker cables are not reversed and connected to the wrong sides (+ and -) on the unit.


Make sure the speaker cables connected to the unit are not shorted. (Check both the unit end and the speaker end.)


Make sure the volume does not exceed the level that the unit is capable of producing.


When using the unit in a rack or other enclosed space, heat may build up inside the unit and cause a fire. When installing the unit, be sure to leave suffi cient space between the top, back and both sides of the unit and walls or other AV components to prevent the internal temperature from rising.


After checking these points, plug in the power cord and use the remote controller to turn on the unit. Turn down the volume before resuming playback. Confirm that there are no problems with the speaker connections and playback performance.


If this symptom recurs, request service at your nearest service center.


In rare instances, the unit may enter standby mode and the STANDBY indicator may blink rapidly, 8 times per second. In this case, unplug the power cord and request service at your nearest service center.

Feb 27, 2011 | Marantz SR7002 6.1 Channels Receiver

1 Answer

Unit will not run. cannot enter diagnostic mode.


i would say that you have a bad touch panel..99 percent positive

May 10, 2010 | Dishwashers

1 Answer

After turning on TV, lamp light blinks but no picture


IF IT SHUTS DOWN TO STANDBY, THEN DIGITAL BAORD IS BAD, IF IT JUST KEEPS CYCLING ON/OFF THEN YOU NEED A POWER SUPPLY, BALLAST AND PROBABLY LAMP

Dec 30, 2009 | Samsung HL-R4266W 42" HDTV-Ready...

3 Answers

Marantz SR6001 AV Surround Receiver - Blinking Standy Light


For resetting sr6001: When power lights blinking, press "clear" + "pure direct" + "7.1 ch input" simultaneously for 3 seconds.


iskender

Nov 10, 2008 | Marantz SR-7200 Receiver

2 Answers

Unit won't turn on.


Is tape(s) in the unit? Are they "shuttling" when you try to power up?...accordianman

Feb 22, 2008 | Emerson EWD2204 DVD Player/VCR

1 Answer

Blinking Green Light on Mitsubishi DLP 52525


the dlp will most likely need a qualified mits repair center to take over for you. repairing that set is pretty involved. and the parts you would need are not available to the public.
on your 48" CRT projection check the DM module for 4 vented 1000mf 16v capacitors. replacement should get you tv working great

Feb 20, 2008 | Mitsubishi WS-48513 48" Rear Projection...

4 Answers

Marantz SR6001 AV Surround Receiver - Blinking Standy Light


Try pressing the power, and multi speaker button at the same time. But first turn the unit off...then press the above buttons at the same time...This is for the SR6001... GH

Feb 16, 2008 | Denon DRA-395 Receiver

3 Answers

Power light just blinks


I have this same problem, it is so frustrating, some movies it will play, and sum movies it will shut of in the middle of it and just blink. You have to un-plug it and plug it back in for it to work.

Jun 06, 2007 | Sony DAV-BC150 System

Not finding what you are looking for?
Marantz SR6001 Logo

988 people viewed this question

Ask a Question

Usually answered in minutes!

Top Marantz Audio Players & Recorders Experts

The Knight
The Knight

Level 3 Expert

74630 Answers

 Grubhead
Grubhead

Level 3 Expert

5259 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Marantz Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...