Question about Computer Monitors

1 Answer

Monitor goes to sleep no input signal only 1 mo old

When the monitor is turned on it says no signal and goes to sleep
the fan also stays on. This computer isn't even a month old.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 153 Answers

Normaly the monitor is not picking up the signal from the PC, it could be VGA cord is not connected, faulty, or the video card is faulty,or the monitor is not compatible to the PC. It could be one of my suggestions. Trouble shoot by connecting your monitor to another working PC and see what happens.If not the VGA cord is faulty and not picking up signal from the PC. Hope it helps.

Posted on Jan 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Monitor goes to sleep immediately after turning on the computer. How can I fix that?


go to start,then pc settings,then monitor or power options the to power and sleep and change on plug to 4 hours and on battery to 10 minutes

Jun 11, 2015 | Computer Monitors

1 Answer

NO DVI INPUT SIGNAL AND MONITOR GOES TO SLEEP


you can't run 2 different inputs at the same time. VGA takes prescedence.

Apr 06, 2014 | HP L1950 Monitor

1 Answer

Monitor goes to sleep when computor is turned on no input signal


If the monitor is going into sleep mode the normal power led will change to another color. This indicates loss of video signal or possible out of range resolution. If the picture goes dark and the power lite stays on, you have a backlight malfunction. It can be bad capacitors causing an inverter power fault or it may have worn out backlights causing a shutdown condition.
Monitor Mike

Aug 17, 2010 | HP w1907 LCD Monitor

1 Answer

No input signal


that is the problem of cpu not a monitor to confirm disconnect signal cable and power on. monitor will show "no signal check signal cable" it means that monitor is ok and fault lies in cpu .then open the cpu and disconnect ram and listen the beep. contineus beep should be heard then ram is faulty replace it. if no beep heard then motherboard is faulty .

Mar 08, 2010 | HP vs17

1 Answer

WhenI turn my monitor on, a screen appears saying VGA input - no signal & DVI input - no siganl & then it goes to sleep


Do you have multiple Video cards installed in your computer?

Check the monitor on another computer to verify the Monitor works and so does the cable.

If Monitor works, cable works, and you have 1 video output from your computer, then your Video card is probably no good.

Jan 26, 2010 | Compaq fs740 17" CRT Monitor

1 Answer

Screen shows message "no input signal" and monitor goes to sleep.


monitor show "no input singnal" error masage when not gating any type of video singnal ,
so if u realy check your monitor wires for correctty plugged in .
then:-

Two possibilities:

either the video/mainboard of the monitor is defective; or
the video card/ CPU is the faulty.

A way to verify is to try the PC with another monitor or to try the monitor in another PC.

thanks

Apr 30, 2009 | HP vp17 Monitor

2 Answers

Monitor goes to sleep and never wakes up


I have called HP Technical Support 6 times about this issue and have logged at least 14 hours into the issue. The things they have done are turn all sleep settings in the "Power Options" in the control panel to "never". The problem persisted. Today, they sent my problem to the complaints department, so maybe they will have the authority to do something for my 5 week old setup.

For me, the monitor was in the "other devices" part on the device manager (go to start menu and type device, and the device manager will show up). I went to HP's website to the support and drivers spot and found a patch for the My Display program. This will allow you to uninstall your monitor, just right click the monitor under "other devices" and click uninstall. After you uninstall, restart and your computer will recognize the and put it under "monitors" in the device manager with the updated drivers. After I did this, the monitor hasn't gone to sleep.

Jan 24, 2009 | HP w2207 Monitor

3 Answers

No DVi input, then computer goes to sleep


I have a new HP pavilion slimline with Vista......a 19 inch flatscreen monitor......I went nuts with it not connecting and saying no DVI input......

I tried something and so far it has worked 10 times in a row...

start out with puter and monitor off.......turn on monitor.......let it go to sleep....then turn on puter....

I have the puter that has the start button on top of it.....not too crazy about it.....

hope this works for you.........Judy in NY

Dec 07, 2008 | HP 22" Widescreen Flat Panel TFT LCD HD...

Not finding what you are looking for?
Computer Monitors Logo

Related Topics:

782 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computer Monitors Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...