Question about Projection Televisions

1 Answer

Beovision 3-32 does not power up - Projection Televisions

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

TV not yet collected.

Posted on Jan 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No power and no lights


Follow power cord to fuse inside and check it, total loss of power usually means a fuse or power supply.

Dec 02, 2012 | Akai PT50DL24 50" DLP TV

4 Answers

Bang & olufsen Beovision 7- Unable to turn television on When trying to turn the television on using the remote. WAIT appears on the top right side of television.


Nice TV set. Try first unplugging the tv for ten minutes, this quick hard reset will drain power from tv, and sometimes it solves the problem when TV is freezing on startup.
If this soes not work there must be a service reset procedure.

Aug 17, 2008 | Projection Televisions

1 Answer

Ok, I have recently been the fortunate one in my family to be given a Philips proscreen 4600 b projector. The only problem, so far, is it will not turn on, at all...think that's why it was given to me...


Hello, welcome to Fixya!

Your unit is having a power fault because it is not switching on. The unit might have worked fine in the past, but that's electronics for you. Power surge, irregular power supply, excess power supply, etc can affect the unit thereby not making it to power on.

First, remove the unit's power cord from the wall, wait for about 30mins, then plug it back in. If it doesn't power on, plug it into another outlet, to make sure there electric current entering into the unit.

If plugging into another power outlet doesn't power it on then it confirms that the unit is having a power fault.

When electric current comes from the power outlet into the unit, it goes straight into the power supply board which then circulates the current into the unit. So if the receiver doesn't power on, the first thing is to make sure there is power entering into the unit.

So check the power cord, if it is a 3-pin plug, it must have a fuse in it. check the fuse if it is not blown. if fuse is intact, then power supply board should be checked.

This unit must have a power supply board in it where power enters from the mains. A capacitor, fuse, diode, etc may have been defective on the power board and maybe that's why its not making the unit turn on. There might also be some disconnection or something, inside the unit which is not making it to power on.

To actually find out what's wrong, you need to disassemble the unit with a screw driver and check what's wrong. You will be needing a meter and continuity tester in order to read the components on the power board. Once you detect any bad component, you can make necessary replacement at any electronics accessories store withing our vicinity. This is the only way by which you can detect and solve the problem.

Of course, testing the power board with a meter will require someone that has the ability. So it you can't, then you might be needing the help of a repairman or you can call a friend that has the ability to help you out.

I wish you the best of luck.

Regards.

Jan 04, 2012 | Philips Projection Televisions

2 Answers

Will not Power up


if you shook it too mutch you must have disconected the power so check all the electricals and fix the separation. the same thing happened to mine

Nov 14, 2011 | Projection Televisions

1 Answer

HAS POWER, WILL NOT POWER UP


Hi

check power supply
if you have power on it
check power button if is not working
try unplug it and connentit after 5 min
if it is not sturting you need to replace
power transformer

Hope I had help you

Nov 25, 2010 | Samsung Projection Televisions

1 Answer

New lamp, new color wheel installed successfully.. tv powers on for about two minutes and powers off, all fans have power, color wheel has power, no power to the lamp? fan on the lamp power supply has...


Powers on and image or no image ? makes a difference. honestly these tvs are prone to many problems that even a trained tech. would have difficulty solving. best to find a reputable company.

Aug 18, 2010 | Samsung HLN617W 61" Rear Projection HDTV

1 Answer

My tv will not power on. It starts to power on, and then the power light starts to flash, and then it powers off and the lights flash really fast


Power supply board it dead.Replaced the power supply board will solved this problems.Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish power supply board for the replacement.

May 03, 2010 | JVC HD-52G787 52" Projection Television

1 Answer

I have a Hisense plasma tv and it will not power up. we had a power surge and it usually powers back up but when the power came back on it didnt power up like it usually does. What can I do?It usuall goes...


Try first unplugging the TV for a couple of hours, after a power surge the TV often stays in protect mode.

By unplugging for a while, you drain power completely, sometimes this can fix the problem.

Nov 12, 2008 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

391 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...