Question about Canon imageRUNNER 3570 Copier

2 Answers

Need your help

Dear Sir. Thank you very much to get your great solving system in line. Now I am especting from your side about trouble. I am a technical person but I don n't have any SERVICE MANUAL regarding that model. It would be better If you Give me the solution of my trouble. My trouble is Canon model iR 3570 E00000----0001. The Best and Regaeds. Abul Kalam

Posted by on

2 Answers

GOOD NEWS BAD NEWS IF YOUR PROBLEM WAS FROM A POWER SPIKE IT CAN BE RESET IN SERVICE MODE.IF NOT YOU HAVE A BAD HEATER UNIT.

Posted on Jul 27, 2007

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 58 Answers

The problem with this code is in the fuser area. I don't have the specific manual for this model, but here's some information from a Canon IR3250 manual: III . Troubleshooting Malfunctions A. Error Codes 1. E000/E003 Thermistor 1) Is the thermistor soiled? YES: Clean the thermistor. Is the thermistor in even contact with the fixing upper roller? NO: Mount the thermistor correctly. Turn off the power switch, and remove the fixing assembly. Measure the resistance between connectors J50B-2 (FSRTH) and J50B- 3 (GNDTH) on the fixing assembly side. Is it between 120k and 290k W? NO: Check the wiring from J222 on the DC controller PCB to the thermistor; if normal, replace the thermistor. Main heater 2) With the fixing assembly removed, is there electrical continuity between connectors J50-3 (FSRN1) and J50-5 (FSRL1) on the fixing assembly side? NO: Replace the main heater. Sub heater 3) With the fixing assembly removed, is there electrical continuity between connectors J50-4 (FSRN2) and J50-5 (FSRL2) on the fixing assembly side? NO: Replace the sub heater. Thermal switch, DC controller PCB 4) Remove the fixing assembly, and detach the wiring cover. Is there electrical continuity between the terminals of the thermal switch? NO: Replace the thermal switch. YES: Replace the DC controller PCB. CHAPTER 4 TROUBLESHOOTING COPYRIGHT © 2000 CANON INC. CANON iR3250 REV.0 JUNE 2000 PRINTED IN JAPAN (IMPRIME AU JAPON) 4-43 2. E001 Thermistor 1) Turn off the power switch, and remove the fixing assembly. Then, measure the resistance between connectors J50B-2 (FSRTH) and J50B-3 (GNDTH) of the fixing assembly side. Is the resistance 1k W or less? NO: Check the wiring from J222 on the DC controller PCB to the thermistor; if normal, replace the thermistor. Power supply assembly, DC controller PCB 2) Replace the power supply assembly. Is the problem corrected? YES: End. NO: Replace the DC controller PCB. 3. E009 Fixing assembly 1) Is the fixing assembly rated at a voltage different from that of the power supply? YES: Replace the fixing assembly so that its voltage matches the fixing assembly. Power supply assembly, DC controller PCB 2) Replace the power supply assembly. Is the problem corrected? YES: End. NO: Replace the DC controller PCB. 4. E010/E011 Connector 1) Is connector J12 of the main motor and connector J218 on the DC controller PCB connected correctly? YES: Connect them correctly. CHAPTER

Posted on Jul 03, 2007

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sir my MHC-RV900D is disply shows push power protection again and again.plz solve my problem. thank u


There is most likely a short in the amplifier that will need to be repaired before the unit will power on normally.

Mar 12, 2013 | Sony MHC-GX40 CD Shelf System

2 Answers

Canon iR-2016 System erro E007


The fusing unit needs to be replaced or repaired. Contact your dealer or service person

Nov 20, 2011 | Canon CLC 1140 Copier

1 Answer

Help...my Avaya Partner 18 phone system is having troubles. When


The processor might be going bad. Call a tech to trouble shoot. That line 3 port might be bad....

Jun 04, 2010 | AT&T Partner 18 Phone (315805B)

1 Answer

My ge side by side fridge and freezer won't get cold please help me


Sir, To solve this problem, you must open the compressor area at the back bottom of the refrigerator and chek the temperature of the pressure line. If the temperature is between 55celcius to 60 than its ok. Or else you need to change the refrigerant. I suggest you to contact the service authority.

Thanks for contacting Fixya.

Sep 09, 2009 | GE (PSS26MSRSS) Side by Side Refrigerator

1 Answer

My ice maker stop making ice,the water is ok,the ice crusher is working. i need help


Sir, To solve this problem, you must open the compressor area at the back bottom of the refrigerator and chek the temperature of the pressure line. If the temperature is between 55celcius to 60 than its ok. Or else you need to change the refrigerant. I suggest you to contact the service authority.

Thanks for contacting Fixya.

Sep 07, 2009 | Whirlpool 25.6 cu. ft. Side-by-Side...

2 Answers

Manual


i was ondering if anywhere in the user manual it solves the problem of the battery not putting power into the camcorder?

May 01, 2008 | Sharp VL-PD1U Camcorder

5 Answers

Canon iR-2016 System erro E007


The erreor code E007 has to do with the fixing ***'y upper film ***'y or roller. It is saying that the film is not moving in and out of "HP" Most of the time it means that the fusing film is torn and not moving properly. If you are getting paper jams in the fusing area and or unfixed or smeared copies. You most likly need to have the fusing film ***'y replaced. It could also be that it is out of place and needs to be readjusted. The only problem is that it's a little tricky to get to and not a bad idea to have a new film to replace the old one while you have it out. Good Luck

Mar 15, 2008 | Office Equipment & Supplies

2 Answers

Unit wont power up


Respected title!I would ask for their help.there is a yamaha dvr-s 120 home theatre my system.Switching on ,writes it ki,"check sp,and then turns off.what may be the problem?I say thank you for their help!with respect:Hornett

Jan 20, 2008 | Yamaha DVR-S120 DVD Player

5 Answers

Canon iR-2016 System erro E007


hi how do solve this problem system error E007

Dec 04, 2007 | Canon CLC 1140 Copier

1 Answer

I need helpl


go to gsm-magic.com and register and start downlaoding

Aug 18, 2007 | Nokia 7610

Not finding what you are looking for?
Canon imageRUNNER 3570 Copier Logo

377 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

old marine
old marine

Level 3 Expert

1774 Answers

Corne Viljoen

Level 2 Expert

385 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...