Question about Canon iR5000-6000-L1 PS Ver 1.0

2 Answers

IR 5000i and iR 6000

1. my IR 6000 show E00061-0001 or E00061-0002 after it is fixed by a technician. Actually it runs well for the first time, except it always gave black spot at the left-bottom corner of A4 or letter-sized paper. But if I set them to R position, it's OK. Then I asked them to be repaired but now the error code above is appeared and I can't even use the machine. What do you think about this?
2. my IR 5000i is turned off for itself and after I turn it on, it shows E00002-0000 code. I try to turn it off and then turn it on again but no effect however. What is this means?

Posted by on

  • danar308 Feb 15, 2009

    Thanks for answering. My 1st problem is resolved. It happens to be the
    technician I once hired was not careful when placing a conector back.
    He broke it and that's the main cause. I called another, they replaced
    it and it is solved. The black spot was because the lamp was misplaced.
    After it was fixed, my machine is running fine now.

    And about my 2nd problem, it sometimes shows me E00002-0000 code, and
    sometimes it doesn't. At the screen, it was hung at the Canon logo
    condition, and can't enter the main page display. They told me it was
    probably because of the main PCB controller faulty. BTW, just curious,
    could it be possible if it's because of software problem?

    Thank you



  • NSIVAREDDY1 May 10, 2009

    E002

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 100 Answers

1 needs a new potential control sensor and pcb. this needs to be installed by a certified tech, However it can be the laser that needs replaced. The procedure isnt fun, this is a difficult problem to resolve.

2. this just needs a new thermistor sensor for the fixing unit. that part shouldnt cost more than 15 bucks. If fixing unit is worn past its life it should be replaced.

Posted on Jan 21, 2009

  • Mike Feb 15, 2009

    e002 error is a fixing unit error. This is the fart in the middle that gets very hot.



    The main board is not bad thats a little dum thing to say. The first thing to check is if the fixing rollers are dirty and worn out. This can happen anywhere between 500 to 1 million pages on the machine. Open the drawer and open the left side delivery assem as if you were removing a jam there. look at the rollers, if they are good your copier most likely needs a new main thermistor.



    Have them install a main thermistor and reset the code. inspect fixing unit and give tell you when it has been rebuilt or how worn out it is. Canon suggest rebuilding them every 500k pages but some can get 1 million if they are used in a heavier manner, like at a big cherch that would use it a lot. Gee I wish I was getting paid something for this lol



    Good luck!

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My IR 6000 show E00061-0001 or E00061-0002 after it is fixed by a
technician. Actually it runs well for the first time, except it always
gave black spot at the left-bottom corner of A4 or letter-sized paper.
But if I set them to R position, it's OK. Then I asked them to be
repaired but now the error code above is appeared and I can't even use
the machine.

picture was pale

Posted on Oct 19, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My canon ir 6000 is showing an error codes E000001-0000 How it will solve?


Your error code is for the fixing unit solve by checking the follwoing:-
1. Fixing lamp.
2. thermistor
3. Fixing assembly if receiving PD
5. if no Potential difference received they the power supply is not okey.

Jul 13, 2011 | Canon imageRUNNER 6000 Copier

1 Answer

Is iR 5000i & iR 5020 LCD Panel same?


they are the same the ir 5000,6000,5020,&6020 are the same

Apr 06, 2009 | Office Equipment & Supplies

1 Answer

Error Code...


Problem 1 is most likely a problem with the primary corona unit... The grid wire is arching to some part of the unit - it code also be that the post wire are strung to loose and the corona wires are bouncing and arching. It sounds like there is something wrong with the corona unit. Have them change the 2 post wires and make sure the grid is clean and that none of the wires are crossed.
Problem 2 A E0002 is a fixing error code. It means that the fuser is not heatting up in time or that is not turning "ON". Most likely you can clear it in service mode, but if that dose not work it could be a blown thirmister or thermal fuse or the fixing lamps or all 3. If it can be reset, the problem may be a power problem from the outlet. Good Luck......

Jan 21, 2009 | Office Equipment & Supplies

1 Answer

Printing envelopes


Dear all,

Im interested this model canon IR-2800/ 2200 /3300 /7200 /8500 /105 /6800 /6000 /5000 /600 /400 / 6020 /5000i /G.P 605/405/ CLC 1140/1180/1120/1100/1150 please kindly quotes us...Here my email add. mapedz_toquero@yahoo.com

May 22, 2008 | Canon imageRUNNER 4570 Copier

3 Answers

PLEASE HELP ERROR CODE


The machine's hard drive has died. you will need to get a Canon technician out to replace it for you and to re-install the machine's system software. In addition to this you will also need to reconfigure some of the machines settings such as the address book, as this is usually lost when the hard drive is formatted or replaced.

May 07, 2008 | Canon imageRUNNER C3220 Color Copier

3 Answers

Error Code description


The Canon is coming on with a code E602-0003 can somebody please help it is only 9 months old and the company we bought it from is out of bussiness. Please email me @ reception@biscayneroofing.com

Thanks
Madlyn

Feb 25, 2008 | Canon (6981A002AA) for imagerunner 2200,...

4 Answers

ERROR c-6000


Hi, enter 10871087 on keyboard of machine, then enter 163.After that press "execute" and start button.machine will restart and will be ready to copy.Otherwise,call service.

BR

Jan 26, 2008 | Kyocera RI-3530 Black and White Copier

3 Answers

Error code on screen is E602-0003


i have problem in my cannon ir 3320 it shows
Error code on screen is E602-0003
E602-001 & E0315-000d
pl solve it

Aug 22, 2007 | Canon (6981A002AA) for imagerunner 2200,...

Not finding what you are looking for?
Computers & Internet Logo

1,216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Computers & Internet Experts

Computer Links

Level 3 Expert

2385 Answers

Tony

Level 3 Expert

2598 Answers

old marine
old marine

Level 3 Expert

1814 Answers

Are you a Canon Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...