Question about Honeywell Programmable Thermostat Heater

1 Answer

Honeywell gas boiler/heater, is not igniting, the water pump works but the burners are not turning on...HELP it is 40deg in the house and 3 kids

Posted by on

  • azboy2g Jan 24, 2009

    Thank you for your response, turns out the inducer motor was blown, i had to order a new one and replace it. the sparks wouldnt go off till there was enough RPMs by the motor. thank you

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

STANDING PILOT, HOT SURFACE IGNITION, OR SPARK IGNITION, NATURAL GAS/ PROPANE OR HEATING OIL

Posted on Jan 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Utica Boiler model # MGB100HD with a Honeywell Aquastat Relay model # Type L8148E will not operate the circular pump. THe damper works and I can hot wire the circulator pump but it won't turn on...


how did you hot wire it. did you jump the wires on the relay board or use another power source? Does the boiler burner start? Have 120 volts incoming to the relay board? You hear relay click when turning power on/off? If so bad relay, or loose wiring terminals on the board. This control has built in transformer that can burn out, that will stop the pump relay contacts from working.

Nov 07, 2011 | Honeywell Programmable Thermostat Heater

1 Answer

I have Drayton Heating System in new home. I seem to be unable to put my central heating on without also having the water heater on. The boiler will come on if the water heating and central heating is on...


you will only be able to have the central heating on seperately if the system is fully pumped. Why would you not want the water to heat? it is more cost effective to use the residual heat to heat the water and keep the temperature up. Costs alot more to heat a cold house and a cold water tank

Nov 06, 2011 | Honeywell Programmable Thermostat Heater

1 Answer

I have a boiler system that was turned off at the thermostat for about 5 min. when turned back on it never clicked on again it has a new honey well aquastat relay, new pilot and prob only three months old....


Take off the thermostat and jump the red and white wires together. The boiler should fire up. If not, you will need to check if the boiler has power to the control. It could be a fuse that burnt.

Feb 14, 2010 | Honeywell Programmable Thermostat Heater

1 Answer

My gas house heater turns on, but turns off in a couple minutes. The heat never starts to blow out. Do you know what the probem may be. The piolot light is light and I just replaced to batteries on the...


It could be a few things, dirty pilot assembly, dirty or bad flame sensor or a bad gas valve or loose wire on the gas valve. Watch the flame as it lights to see if all the burners light. If not you will need to clean the burners and flame tray that spreads the flame to all burners. Good luck!

Nov 11, 2009 | Honeywell Programmable Thermostat Heater

1 Answer

Boiler is a baxi control for heating is honeywell.


this will be your diaphram inside your divertor valve.
the one that looks like a spaceship.
it will e split.

Oct 05, 2009 | Honeywell Programmable Thermostat Heater

1 Answer

Cannot get central heating working,for honeywell ST6400 programme


with y plan 3 connections on programmer HW on HW off CH on HW on to cylinder stat then HW call to Orange on Mvalve to power boiler and pump HW off to grey wire on Mvalve to close hot water CH to room stat common then heating call to white on Mvalve

Jun 13, 2009 | Honeywell Programmable Thermostat Heater

1 Answer

No hot water honeywell st6400c


HW valve was stuck in the open posiion and the micro-switch was not working so thats why boiler and pump were not starting. Bled system to below the level of the valve to be changed, and replaced valve with a drayton ( easy quick change of valve head if needed no screws )

Sep 07, 2008 | Honeywell Programmable Thermostat Heater

2 Answers

No heat!


Ger, do you get your hot water off the same boiler and it that working alright? How many zones and are they controled by zone valves (little boxes mounted on the pipes) or circulators (small pumps)?

Boiling water sounds can indicate hard water deposits in the boiler or that your aquastat is set too high allowing the water to heat up higher than it should. Check your boiler guage and let me know what temperature you are recording. Get back to me with the answers to my questions, we'll figure it out.

Nov 27, 2007 | Honeywell Programmable Thermostat Heater

Not finding what you are looking for?
Heating & Cooling Logo

300 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honeywell Heating & Cooling Experts

Bill Long

Level 3 Expert

587 Answers

paulcarew

Level 3 Expert

2047 Answers

Brandon Berry
Brandon Berry

Level 2 Expert

407 Answers

Are you a Honeywell Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...