Question about Samsung HL-P5063W 50" Rear Projection HDTV

1 Answer

Have picture lose picture tv turns off and on

Have picture and sound after a few min lose picture still have sound also no vol and mute function, tv will not turn off with remote or main on/off button have to unplug from wall. replug tv and sometimes have picture for a few min then tv turns off and on meanwhile all three led lights are flashing. lights do not flash all the time only while tv is turning off and on

Posted by on

  • Anonymous Feb 28, 2009

    I have the same problem,but when I power it down and let fan cool the lamp I'm able to turn the tv back on have picture and sound for a couple minutes until it happens again.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 159 Answers

The lamp has a life cicle. if yours is been used a lot. then the lamp has to be changed. when the tv cannot turn on steady and gets off imm. the computer inside the tv tries to turn off the set but the lamp charges again and the micro tends to keep working. the first step to take in this tv is to change the lamp to eliminate this common source of problems

Posted on Apr 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Watching tv last night and the tv went blank,no picture but still had sound.had this on all channels.is there a projection lamp on this tv ?


You have a CRT projection TV. There's no lamps in this that can be swapped out. The technology is very similar to a glass tube CRT TV.

If the picture disappeared but you still have sound then you haven't pressed the wrong input or pressed the picture mute because sound would go too. As a quick check, try any function (vol, contr, bri etc) that normally brings up an onscreen display. If that has gone too then it's a TV issue with the drives to the three tubes. If the OSD is still visible, then the problem is either a source signal issue (broken or disconnected cable; menu changed to affect the signal output of an external source) or the TV isn't processing the signal correctly.

For TV problems where something has broke, the answer is getting the TV repaired or replaced.

Sep 12, 2014 | Projection Televisions

1 Answer

Very odd problem


It is a fault with the control board or with panel.

Aug 24, 2008 | Philips 43P8341 43" Rear Projection...

1 Answer

I have replaced the TYLA-1000K lamp and housing, plugged the TV back in, turned TV on, pressed vol- & mute and nothing happens. The flashing green light comes on for about 3 to 4 seconds and then it...


amber is the colour...remove LAMP assembly...properly re-insert LAMP assembly back into TV...make sure it looks secure....close door and tighten screw.....door MUST be shut properly or TV will not operate correctly..it sounds too easy i understand TRY it you might be surprised!!!

May 19, 2010 | Projection Televisions

2 Answers

A brief history: fixya helped me change my bulb (been receiving a "replace bulb" message for awhile until my picture went black). The picture now is snow, not black which seems to me to indicate the bulb...


Since you do have sound but snow for picture is your TV 54J or 54U chassis the PT50DL54J chassis shows 4 tuners also Have you look for Leaky or Bad capacitors if they are puffed up on top they are Bad 2200uf 25v 1000uf 25v Look for bad capacitors on tuner Boards, and I have seen where they are on Power supply board that will affect Picture.

Dec 04, 2009 | Panasonic PT-50DL54 50" Rear Projection...

1 Answer

Temporary losing picture


CHCK THE OPTIONS MENU SEE IF IT HAS A COLOR CONVERSION OPTION ,,TRY THAT,,ALLIGN THE COLORS

May 14, 2009 | Pioneer SD-582HD5 58" Rear Projection...

1 Answer

Corner convergence for panasonic pt51hx40c projection tv


Yes there is a Service Code you need in order to set convergence and on this set it is not easy to enter! 1) Switch Antenna to cable (2) Set Sleep Timer to 30 mins,Exit menu Enter ch 124 (3) Now Press vol- on front of TV / A red CHK should appear on screen / NOW enter menu and turn sleep timer off / Exit again,now Press Power untill you see 0V00 press ch up untill you see 0V1 Then Press vol+ you should now have convergence Pattern on screen. To adjust use (ch- ch+ and vol- vol+) (cursor) moves to where you want to adjust (mute) locks place you want to adjust RTune changes R-G-B when done make sure you Save adjustments.

Jan 04, 2009 | Panasonic PT-47WX49 47" Rear Projection...

1 Answer

Picture comes in and out


you can fix this problem, your light bulb in the tv is on its last leg, and needs to be replaced, usually around $100-$200.

Sep 30, 2008 | RCA R52WH73 Projection Television

2 Answers

Black box on screen


This happened to me and it turned out the closed captioning on my TV were activated somehow. I never even touch the controls on the TV but I had to manually check the settings on the TV and found that the captions were on.

Sep 16, 2007 | Mitsubishi VS-6041 60" Rear Projection...

Not finding what you are looking for?
Samsung HL-P5063W 50" Rear Projection HDTV Logo

407 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

Donald Griswold
Donald Griswold

Level 1 Expert

8 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Are you a Samsung Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...