Question about Ionic Pro CA200B Air Purifier

Open Question

The red clean button stays on

I have air purifier shown on your site and i have cleaned the blades but the clean light comes back on after i have had it on for about 10 min

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: clean button

My ionic pro did the same, the red light just wouldnt go out, so I looked down the plate opening, (with unit unplugged), and could see one of the wires was broken. (these are the ones you clean by pulling up that plastic tab). I am currently looking for replacement wires, will post my progress. GregV

Posted on Nov 28, 2007

Ad
  • 1 Answer

SOURCE: CA200 red light stays on, wont turn on

The machine is now part of a land fill elsewhere. Do to the company's attitude and refusal to help figure out what was wrong, they will not get another dime of my money. It seems that - when I tested - several of the components were zapped. I found at least one z diode out on the power supply end. I was not about to start fooling with the flyback xmfr. What amounted to the chrona wires tested fine. It is a neat idea but the company is worthless as far as customer relations. The "service" person could barely speak English (Engrish). They did not know a transistor from a fuse! I will recommend this product TO NO ONE. Ionic Pro - are you listening??? A VERY DISSATISFIED CUSTOMER!!!

Posted on Jun 09, 2008

rdanner3
  • 3 Answers

SOURCE: ionic pro won't turn on

Solution, perhaps...

All electrical contacts can get a film on them. Try cleaning the contacts (at the bottom of the blade unit; you should see the three with the blades out) with an alcohol swab (make sure the contacts are dry before reassembly in this case) or a pencil eraser (vacuum the debris out before attempting to start it again).

If those contacts don't make up properly, the unit will think it needs cleaning, even though it doesn't.

Posted on Feb 23, 2009

  • 12 Answers

SOURCE: My air purifier dirty light keeps coming on, and

it obviously has a problem with the wiring. take it apart and make sure no exposed wires are crossing (wires without insulators) and make sure that none of the wires are disconnected

Posted on Jan 24, 2011

  • 41 Answers

SOURCE: My Turbo Air Purifier shuts

Hi jerry bauer,

I work for the Ionic Pro company. Please call customer service at 800-875-8577 and they will be happy to assist you. Thank you, Mary

Posted on Feb 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reset oreck XML professional


The reset button is power button,look at what it says under cell check button, hold(symbol) button t reset.

Jan 27, 2013 | Oreck XL® Air Purifier

2 Answers

Blue flashing light on lumipure air purifier


I read on another site to hold the power button down for 5 seconds. Dont know what the blue light is but this stopped it from flashing!

Jun 13, 2009 | Sharper Image Ionic Breeze GP SI730 Air...

1 Answer

Red light stays on continually.


Same problem : after cleaning thoroughly inside by removing the Front & Rear Plastic grid and the stainless blades, I also cleaned the 2 wires (very softly and carrefully, not to break them), but the Red light goes on after only few minutes :

Here is my last Solution :
1 - Turn on (Low position) although the Red ligt is on
2 - Release the Rear plastic Grid (or Front plastic grid, or both of them) : That stop the unit automatically
3 - Replace it and make sur it's well locked : the unit turns on automatically.

After that, my unit works well, no mor Red light.

But my husband will see if he can by pass the Cleaning detector, so we will not have this stupid Red light on anymore !

Good luck.

Feb 22, 2009 | Sharper Image Ionic Breeze 3.0 Air...

1 Answer

The red cleaning light is staying on after I have cleaned it several times


I have had to hit the power button several times in a row to get the red cleaning light off till the other light went blue. Thats what I did, Did you just clean the blades? there is another part that cleans the wires too, Its like a plunger.

Dec 07, 2008 | Ionic Pro CA200 Air Purifier

4 Answers

Red Cleaning Light won't turn off


After cleaning the unit, replace the grid into the unit. Hold upside down for at least 30 seconds to reset.

Jul 19, 2008 | Sharper Image Ionic Breeze GP SI730 Air...

2 Answers

RED CLEAN LIGHT


After cleaning the unit, blue light turns on momentarily then red cleaning light comes back on. Have cleaned and dried unit including the contacts on the end (cleaned with alcohol). Sounds like a common problem, any solution?
Bob

Jun 17, 2008 | Ionic Pro 901P2RIP04 Air Purifier

1 Answer

Ionic Pro Turbo air purifier


i have the same problem after cleaning it it turned on with a sound like frying stuff .and it goes to red light which means clean..but the blades are clean i dont know whats goin on but theres a smell in the unit which i cant tell what kind any one can help?

Jun 05, 2008 | Ionic Pro TURBO Air Purifier

1 Answer

Red Cleaning Light is On


I have the same problem. I totally took the unit apart and cleaned it out. After I reasembled it, the same thing. Just that little cleaning overdue light on. I can tell that it is not working as well as there is no breeze coming from the front. That is what I get for buying a serviced unit.

Nov 25, 2007 | Sharper Image Professional Plus Ionic...

6 Answers

CA200 red light stays on, wont turn on


The machine is now part of a land fill elsewhere. Do to the company's attitude and refusal to help figure out what was wrong, they will not get another dime of my money. It seems that - when I tested - several of the components were zapped. I found at least one z diode out on the power supply end. I was not about to start fooling with the flyback xmfr. What amounted to the chrona wires tested fine. It is a neat idea but the company is worthless as far as customer relations. The "service" person could barely speak English (Engrish). They did not know a transistor from a fuse! I will recommend this product TO NO ONE. Ionic Pro - are you listening??? A VERY DISSATISFIED CUSTOMER!!!

Jul 07, 2007 | Ionic Pro CA200 Air Purifier

4 Answers

Ionic pro won't turn on


Solution, perhaps...

All electrical contacts can get a film on them. Try cleaning the contacts (at the bottom of the blade unit; you should see the three with the blades out) with an alcohol swab (make sure the contacts are dry before reassembly in this case) or a pencil eraser (vacuum the debris out before attempting to start it again).

If those contacts don't make up properly, the unit will think it needs cleaning, even though it doesn't.

Mar 27, 2007 | Ionic Pro 901P2RIP04 Air Purifier

Not finding what you are looking for?
Ionic Pro CA200B Air Purifier Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ionic Pro Air Purifiers Experts

Paul Cox

Level 1 Expert

4 Answers

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14363 Answers

Are you an Ionic Pro Air Purifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...