Question about GoVideo Go Video DVD/VCR Combo

Open Question

I have a cinevision DVR1000 dvd/vcr combo. I need to hook it into my dish network satellite system but need a 3 digit code for the cinevision DVR1000 to do so. I can't find the code anywhere. Can you help?

Posted by on

  • Anonymous Jan 24, 2009

    me to

×

4 Suggested Answers

  • 1003 Answers

SOURCE: Remote control device

you can use a universal remote that allows vcr and DVD operation go to walmart, radioshack, or target

Posted on Jan 15, 2008

SOURCE: Cinevision DVD Recorder/VCR does not record.

i am looking for a manual for my cinevision rv 4000 does anyone have one I can buy

Posted on Feb 04, 2008

  • 2 Answers

SOURCE: magnavox dv225mg9 dvd/vcr player. Hooked

I had the same issue. You probably have your unit connected with the newer cables that are red, blue and green. These are more sophisticated and offer better quality for the DVD portion. However, they will not carry the video for the VCR, only the audio.
You need to connect a *yellow* Video Out cable from your DVD/VCR to the Video In on your TV, this should carry the video for the VCR! Hope this helps!

Posted on Jan 05, 2009

ltfrc
  • 227 Answers

SOURCE: Would like to record from my tv to my magnavox dvd/vcr combo box

If I understand your request right, You do not have cable or satellite box.
You can not record from your TV. You use the TV as a monitor from the dvd/vcr combo box. What the box receives is what shows on the TV. So you will have to have a digital convertor hooked to the (antenna in) dvd/vcr combo box, (antenna out to the tv antenna in) Depending on the antenna you are using that is on the other end of your cable-in coax connection this will hook to your antenna in on the digital convertor box. If your cable is hooked up and operating correctly and directly to the tv that is digital ready you probabbly have a good picture. When the vhf/uhf signal was transmitted you could go from the dvd/vcr to the tv with no problem. But now that the signal is digital and the tv is set for digital the dvd/vcr will not pass a digital signal to the tv. Best suggestion, you have to get a digital dvd/vcr receiver. If you have more question please contact me.

Mike

Posted on Jul 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What code to use for a 5.4 ir echostar dishnetwork remote


Hi there, Cheri Torres with DISH Network Customer Service here. I came across your post and wanted to help. I will list here for you the best codes for a 5.4 IR remote to try with a Go Video DVD/VCR combo. I hope this information is useful and if you have any other questions please let me know.

5.4 IR remote - 1693, 1822, 1569, 1692.

Instructions for addressing the remote to the DVD/VCR combo
1. Press and hold down the AUX button until all the mode buttons light up red.
2. Enter the four digit code.
3. Press the pound(#) button once.
4. Try the functionality of the device.

Oct 12, 2011 | GoVideo Go Video DVD/VCR Combo

1 Answer

Can you tell me the 3 digit nunber to make my dvd/vcr compatable with dish network tv?


We would be happy to help you with getting your DISH Networkremote to control your Sanyo DVD/VCR combo unit. Pressand hold the VCR/DVD button located on the top of your remote until all mode buttonback lights come on, then release. Use the number buttons to enter thecodes for your Sanyo DVD/VCR combo unit; here some of the codes we currently have: 549, 583, and 608. Press the pound (#) button. To check that the codeworks try several different functions on the remote to make sure it willproperly operate the TV. Keep in mind that some codes may not be compatiblewith your equipment. If this is the case, try the other codes listed for thatdevice until you find one that is compatible with your equipment.
If you were not able to get your DISH remote to work with it with the codes provided, try a power scan. Pressand hold the VCR/DVD button located on the top of your remote until all mode buttonback lights come on, then release. Press and release the power button. Press the Up button once a second while pointing the VCR/DVD combo unit. If the code for the equipment comes up, it will power off. Press the pound (#) button.
We hope this help and thank you for being a valued DISH Network customer!


Phillip Chang
DISH Network Customer Service Representative

Feb 04, 2011 | Sanyo DVW-6000 DVD Player/VCR

1 Answer

I have a vcr dvd combo and i want the code for my dish network remote so i can use one remote please


We would be happy to help you with that. Here is a list ofcodes that should address your DISH Network remote to your Emerson DVD/VCR combo unit: 588, 505, 506, 518, 534, 536.

Press and hold the DVD/VCR button located on the top of the remote until allthe mode buttons at the top of the remote light up, then release. Use thenumber buttons to enter one of the codes for your Emerson DVD/VCR combo unit, thenpress the pound (#) button. If the code entered is valid for the remote, themode light flashes three times. .To check that the code works try several different functions on the remote tomake sure it will properly operate your Emerson component. Keep in mind that somecodes may not be compatible with your equipment. If this is the case, pleasetry the other codes listed for that device until you find one that iscompatible with your equipment. We hope this helps and thank you forbeing a valued DISH Network customer!


Phillip Chang
DISH Network Customer Service Representative

Jan 20, 2011 | Emerson EWD2203 DVD Player/VCR

1 Answer

How to hook up dvd/vcr combo to a tv with dish satellite


Run the line level outputs (red,white, and yellow), from the satellite receiver into the "In" terminals on the dvd/vcr...then run the line level outputs from the dvd/vcr to the inputs on the tv

Dec 27, 2010 | Philips Magnavox DVD/VCR Dual Player

1 Answer

Looking for a code to use on my Dish Network (Universal) remote in order to operate my Emerson Model EWD2202 Combo VCR/DVD player


Hi my nameis Mike Houston of DISH Network and I was going over your post and see whereyou want the codes to program the DISH remote to the Emerson DVD/VCR. We do nothave the three digit codes to enter however we do have what we call a PowerScan and it will allow programming the remote to the Emerson player, I willsend a link to help with these steps. http://www.dishnetwork.com/SupportSection/power-scan-instructions

Oct 31, 2010 | Emerson EWD2202 DVD Player/VCR

1 Answer

Need codes for toshiba remote to work cinevision DVD/VCR player


There aren't any, your brand isn't supported on your Toshiba remote. The only thing you can do is to try all the other codes, maybe you're lucky and one of them will.

Jul 11, 2010 | Toshiba Cinevision DVD/VCR Combo

2 Answers

Would like to record from my tv to my magnavox dvd/vcr combo box


If I understand your request right, You do not have cable or satellite box.
You can not record from your TV. You use the TV as a monitor from the dvd/vcr combo box. What the box receives is what shows on the TV. So you will have to have a digital convertor hooked to the (antenna in) dvd/vcr combo box, (antenna out to the tv antenna in) Depending on the antenna you are using that is on the other end of your cable-in coax connection this will hook to your antenna in on the digital convertor box. If your cable is hooked up and operating correctly and directly to the tv that is digital ready you probabbly have a good picture. When the vhf/uhf signal was transmitted you could go from the dvd/vcr to the tv with no problem. But now that the signal is digital and the tv is set for digital the dvd/vcr will not pass a digital signal to the tv. Best suggestion, you have to get a digital dvd/vcr receiver. If you have more question please contact me.

Mike

Jul 25, 2009 | Philips Magnavox DVD/VCR Dual Player

1 Answer

Dish Pro record code for Mag combo


ZNREL, I've done this with Dish Pro before. Setup the Dish remote to control the Mag combo in the VCR position. Press the SAT button and select the guide. Go to the program in the guide and select it. The "record this program" routine should pop up, set it up. Here's the key, make sure the Dish remote has the VCR button selected and that the remote is placed where it can "see" the Mag combo. At the set time, the Dish remote will change the DishPro to the proper channel and then issue s "record" command via infrared to the Mag combo to start recording. DishNet has all of the device codes to their remotes downloadable from their site.

Mar 05, 2008 | Philips Magnavox DVD/VCR Dual Player

1 Answer

Remote control device


you can use a universal remote that allows vcr and DVD operation go to walmart, radioshack, or target

Jan 15, 2008 | GoVideo Go Video DVD/VCR Combo

1 Answer

Finding a code


Look under Funai with dish network.

Nov 19, 2007 | Philips Magnavox MWR20V6 DVD Recorder/VCR

Not finding what you are looking for?
GoVideo Go Video DVD/VCR Combo Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top GoVideo DVD & Blu-Ray Players Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

 Grubhead
Grubhead

Level 3 Expert

4590 Answers

Are you a GoVideo DVD and Blu-Ray Player Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...