An expert who has achieved level 3 by getting 1000 points
An expert that got 10 achievements.
An expert that got 5 achievements.
An expert whose answer got voted for 100 times.
Re: RCA R29T01BA COLOUR TELEVISION
It's probably transistors on the crt board or caps in that control circuit. Not an expensive repair and worth doing... That particular model can still be fully rebuilt...
Not a difficult chassis to pull and you could send it in to Tri-State Module for a complete rebuild... Or just find a reputable repair center locally and take them the TV for repair..
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
I HAVE AN
Bosch TDS 1445/05 Sensixx AND THE IRON PLADE NOT WORM AT ALL.
I CHECK THE POWER.I CHANGE THE THERMOSTAT/THE CONDENSER WITH THE LAMP/.BUT STILL NOT WORK.
THE BOILER WORK GOOD.PLEASE HELP ME.WHAT CAN I DO MORE. THANK YOU
If you have an issue where your picture turns off and the green power light starts flashing, you are most likely looking at a weak or old lamp. Do not be confused with a pix loss and a RED light flashing, as this can be caused by many things. The normal sequence of events for this fix is this: 1) TV turns on normally, plays for 1 to 3 minutes (may be more or less time) 2) Picture goes out and green power light begins flashing. It may flash for up to 2 minutes 3) green light turns on solid (stops flashing) and picture returns. 4) Picture goes out again and process repeats.
You may have been told that "if the lamp light isn't on, it isn't a bad lamp". FALSE! A weak lamp will cause the process above to occur. Other signs of a weak lamp: The reflector in the lamp is very cloudy You may see a "growth" or "bubble" on the vertical glass tube which is the lamp You haven't replaced the lamp in quite some time or it is the original lamp from when you purchased the TV.
In cases like these, try a new lamp. Stick with an original Sony lamp, as there are many stories (both personally witnessed by me and also documented on the web) about problems with after market replacement lamps. And remember, lamps DO NOT have a shelf life; you can store them in a good environment (not too hot or cold!) for an indefinite period with no ill effects.
The longer bolt has nothing to do with it not starting. Vacuum leak could but unlikely. Either your starter is getting overheated from heat transfer from the engine, or the distributor timing isn't set right. I would check the timing first and find TDC and rest the distributor into the block. If you need a video for reference, check out YOUTUBE.COM and search set timing on whatever engine you decide to check.
Just replace its Lamp and procedure is written in user manual of KDS-R50XBR1 F93087600
XL-5100 LAMP BLOCK Lamp is available in Sony Accessories and price is $250 Always buy Sony original lamp for good picture in TV and avoid aftermarket / cheap lamps that can cause damage of TV circuits. Click Sony Support to download Instruction Manual copy, if you want it.
Not sure what causes it but it can be fixxed by your local repair guy, I just had mine fixxed for under a hundred bucks, he takes the back off and with a tiny screw driver adjust a few screws to near brand new perfect picture.. and it has been good ever since
Try replacin a new display card. If it is fine working.ok
If not try fixing for cold solder in the video section.
I suggest video section according your report the light green LED lighted that shows the power section is doing fine.
If it's working fine in DOS, it can only be your display drivers for your operating system. What happes when you start in SAFE MODE? When you PC starts, keep pressing the F8 key, go to Safe Mode. If it works, bring the Resolution down to 800 X 600 and load the new display card drivers. Restart, should be fine.
you are having a problem in your video circuit and your tunner section if the green is smooth also have the deflection ic checked.but this set needs to be taken to a qualified tech repairs could cost about $1oo.00 good luck.