Question about Royal 1610X Shredder

1 Answer

Won't shut off

Won't auto shut off

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,904 Answers

You have an optic sensor that is blocked or shorted. If you take it apart you should be able to identify the problem. It is up by where the paper feeds in.

Posted on Jan 09, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

C200 Car shut off whilst I was driving. It has some power but won't crank over. Replaced the crankshaft position sensor and the car still won't crank over. Auto electrician said he was unable to scan


try to bypass the starter motor see the diagram attached.
If there are not function, test the ignition coil+PCM+BCM, etc any part can be faulty. 0161719d-dff5-4726-a652-08d0f17e7066.jpg see the diagram, get another information from another scanner repair shop.
God bless you15f71ec8-d658-438e-9813-a33ae1bc0136.jpg245792b1-b6d6-44f4-972a-8c2aedbe0f3e.gif

Jul 10, 2013 | 1998 Mercedes-Benz C-Class

1 Answer

Electric blanket won't heat


Take the help of your mattress pad company or look into instruction manual. Do not operate it unless you are familiar with it. You should call the customer care to know how to operate.
Jack from Coriumdirect Mattress pads

Apr 07, 2013 | Biddeford Blankets Heated Mattress Pad...

1 Answer

Starts and shuts off and wont stay running.


It sounds as if your bypass needs to reset as well. What's the year, make and model of your vehicle?

Jan 27, 2013 | Prestige Remote Start

1 Answer

Heil furnace blower motor stays on won't shut off at thermostat blows cold air continuously


Do you have t sat fan switch in on position??? If so blower will run continously set it to auto and it will cycle with heat call

Nov 12, 2012 | Heating & Cooling

1 Answer

Can't get my vcr off auto. It keeps flashing and vcr won't shut off. Can't get to the menu long enough to see how to shut it off


Try unplugging the VCR for 20 seconds and plugging it back in. It probably will still flash because the clock needs to be reset but you should be able to turn it on and off.

Feb 21, 2012 | Televison & Video

2 Answers

1998 chevy s10 driving along and engine shut down.after sitting 10 min.it started but was rough.went 100.ft and it shut off again.sat for a while.it started and ran a couple miles like nothing was ever...


if it shuts off while driving and will not start back up for at least 10 minutes, then it may be the crank sensor doing this. is check engine light on! if so get it scanned to find problem code. if no scanner, auto-zone will scan for free. if light is on. CPS symtoms are: car dies and won't re-start till it cools down, or won't start at all. good-day ! crank sensor timing will be out of sync. it controls timing and sends info to pcm.

Jul 19, 2011 | 1998 Chevrolet S-10 Pickup

1 Answer

My iron's MODEL: 14977Z The iron's red light is on but won't heat to iron. was working a couple of hours ago


This is typical of a iron, it is cheaper to replace than to repair. The heating element is broken.

Jun 02, 2011 | Hamilton Beach 14977 Iron with Auto...

1 Answer

I have a 1994 jeep grand cherokee manufactured in October 1993. The problem I'm having is that the jeep wont start. At first we had no gas, no spark. We checked crankshaft sensor...it's ok, but...


Try this. Lock and unlock the tail gate with the key and see if it will start. The battery must be hooked uo when this procedure is followed. Whenever the battery is disconnected, the security circuit shuts the ignition down.
When you hook up any battery, make certain that you connect the positive battery cable first and negatvie (ground) second.

May 16, 2011 | Jeep Grand Cherokee Cars & Trucks

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Royal Office Equipment & Supplies Experts

James Cagle
James Cagle

Level 2 Expert

453 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Michael Vincent Cruz

Level 3 Expert

868 Answers

Are you a Royal Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...