Question about Nordic Track Treadmill Motor Controller Mc5100dts-50w 37376 Pn 285703 -

1 Answer

NORDICTRACK X9I CALORIE COUNTER IS WRONG

Repairmen said Controller is nothing to do with the calorie counter but yet Console and Rear roller was replaced so what else could it be or is it the controller

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nordic Track Master
  • 12,223 Answers

Yes the repairmen is o.k when he says the controllers nothing to do with the calorie counter.
See the block diagram attached, the problem is the display board or upper board. However adjust the REED switch, test for open or faulty, clean it, and tigh very well the connector b) tight the ribbon cable for keypads inside the display board. c) replace batteries from display by new one, with the same polarity, same markay such hybrid rayovac. c) clean the contacts battery.
God bless you
NORDICTRACK  X9I CALORIE COUNTER IS WRONG - 1_8_2013_6_39_01_pm.gif1_8_2013_6_39_20_pm.gif

Posted on Jan 08, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 40 Answers

SOURCE: Nordictrack motor will not run when start button is pushed.

Likely the cover of one of the motor brushes popped off. Unplug the machine before you pop it back in place, then try it again.

If that doesn't work, most likely it's the motor control board, or possibly the console, or finally just a loose connection behind the console.


But most likely, it's the motor brush cover. I've been seeing that alot with this model.

Posted on Nov 01, 2009

ercupa190
  • 12223 Answers

SOURCE: NordicTrack ASR 630 Elliptical Console isn't working

1) replace new batteries with the same type, and o.k polarity.
2) clean the contacts batteries with c.cleaner and retight the spring with plier for a GOOD contact.
3) adjust the REED swtich, test it , clean it and tight the plugs
4) tight the ribbon cable inside for a good contacts keypads.
God bless you

11_27_2012_11_26_14_pm.gif11_27_2012_11_26_37_pm.gif

Posted on Nov 27, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

6 Answers

Do over the counter weight loss pills actually work?


There are many products to aid weight loss that you can buy over-the-counter. Some are safer and have been regulated more than others. It's very important that you do your research before you buy.

Whatever you choose, you need to combine it with a lower calorie diet and exercise and it's best to consult with a doctor.

Feb 20, 2013 | Health & Beauty

1 Answer

C2255 treadmill - everything works but the console light no longer comes on - nothing in manual to show what the problem could be.


If the console takesbatteries, replace them. If this does not work or your console does not requirebatteries, check the reed switch or optic sensor. Reed Switch:Unplug the treadmill and remove the motor hood cover. The reed switch is mountedon the frame next to the front roller pulley. There is a magnet glued into thefront roller pulley. When adjusting the reed switch, make sure it is pointingdirectly at the magnet. Move the tip of the reed switch within 1/8" of themagnet. Also, check to see that the wire is not damaged, and is connected tothe console.
See the diagram adjust for 1/8"

After that: Do the next: 1) Tight the flexible cable from keypanel vs Display board.2) Tight the connector from Display Board vs Lower Board( Main Controller Board). See the block diagram that I did how the main controller board has aprox 90% of function from the any treadmill
11_28_2011_5_21_01_pm.gif11_28_2011_5_21_21_pm.gif

Nov 26, 2011 | Nordic Track C2255 Console (treadmill)

1 Answer

Treadmill won't start. Console works but when push start or any of the buttons it beeps and nothing happens. It incline, change speed. I unplugged and restarted but nothing.


If the console takes batteries, replace them. If this does not work or your console does not require batteries, check the reed switch or optic sensor. Reed Switch: Unplug the treadmill and remove the motor hood cover. The reed switch is mounted on the frame next to the front roller pulley. There is a magnet glued into the front roller pulley. When adjusting the reed switch, make sure it is pointing directly at the magnet. Move the tip of the reed switch within 1/8" of the magnet. Also, check to see that the wire is not damaged, and is connected to the console
.
Optic Sensor: Unplug the treadmill and remove the motor hood cover. The optic disk and sensor are located either at the end of the motor or the right hand side of the front roller. The optic disk spins between two sensors on the optic switch. The disk must spin freely without touching either sensor. The sensors can be moved by loosening the adjustment bolt holding the switch to its bracket. The switch can then be slid. Center the disk.
11_21_2011_11_34_59_pm.gif11_21_2011_11_35_24_pm.gifRemember the Display Console Board has circuit that send to PController Motor, and after you did the adjustment you can conclude if the Sensor Reeed is faulty, 2) The Display of 3) The main Controller Motor.

Oct 29, 2011 | Nordic Track C2255 Console (treadmill)

1 Answer

The waling belt seems to be loose and not centered how can I fix this


Dear Sir:
Please wathc this videos:

http://www.youtube.com/watch?NR=1&v=USSgbsZbDLQ
http://www.youtube.com/watch?NR=1&v=KiEZDNe0F8Q
http://www.youtube.com/watch?v=wjrVjYe2LYQ&feature=related
Removethe key from the console.
    • 2
Unplug the power cord.
    • 3
Ifthe walking belt shifts to the left, turn the left rear roller bolt 1/2 turnclockwise with an Allen wrench.
    • 4
Ifthe walking belt is off center to the right, turn the right rear roller bolt1/2 turn counter clockwise with an Allen wrench.
    • 5
Plugin the power cord.
    • 6
Replace the console key.
    • 7
Aftera few minutes of running the treadmill, check to see that the belt is centered.If not, repeat the steps.If you need further assistance, please reach me, sincerely G-d bless you.

E.CUADRA
MANAGUA, NICARAGUA. C.A.

Oct 26, 2011 | Spirit ® XT275 Folding Treadmill

1 Answer

Our Weslo Cadence Dx12 treadmill will only operate at the highest speed and will not turn off without the safety key. The speed cannot be adjusted to slower speeds.


Go to Radio Shack and buy some contact cleaner. Clean the peed control on the console. If that doesn't solve the problem, you will need to replace the motor controller PCB..

Dec 11, 2010 | Treadmill Doctor Weslo Cadence Dx12...

1 Answer

I don't knowhow to get the electronic calories counter to begin registering once I begin exercising


Have you tried the unit manual operation? The calorie and time feature should work without you plugging in age or weight. Now if the time is working .but calories fail then you have a upper console problem, if both are not registering most likely then it is a sensor problem. Not knowing what type of unit you have can't exactly to pin point components. But this a good starting point. Good Luck!

Mar 23, 2010 | Exercise & Fitness

1 Answer

Error E000 on Canon NP 6317.


IX. SELF DIAGNOSIS The DC controller PCB has a microprocessor that diagnoses the functions of the copier (particularly the sensors) at appropriate intervals. If this microprocessor detects an abnormality, it will display the type of the abnormality on the indicator on the control panel. The table below shows the various fault codes, their meaning, and the corresponding detection timing. Example of E000 code indication: Eó000 light alternately. Fault criteria • If the temperature difference between the thermistors 1 and 2 is 60°C or higher. • If the fixing asssembly temperature is lower than 50°C after 15 sec from the power-on. If the tempereture remains 220°C or higher for 0.1 sec or longer. If warm-up is not over after 60 sec from when the temperature reached 50°C. If fixing unit temperature drops below 50°C when the copier is in stand by or copying. If the C HEAT CHECK signal is on while the HEAT ON signal is off. If the main motor speed feedback signal does not appear after 2 sec from the main motor. If the break signals is generated continuously for 0.1 sec or more when the counter is not being driven. Code displayed Main cause Fixing roller heater (LA1) low temperature error Thermistor1 (TH1), Power supply assembly, Fixing roller heater (LA1), or DC controller PCB Fixing roller heater (LA1) low temperature error: Thermistor, fixing roller heater, AC driver, power supply assembly, DC controller PCB, thermoswitch (F1), auxiliary thermistor (TH2) Fixing roller heater (LA1) low temperature error: Thermistor (TH1), fixing roller heater, power supply assembly, DC controller PCB, thermoswitch (F1), auxiliary thermistor (TH2) Fixing heater ON timing error: Triac (U104) on power supply assembly Main motor error: Main motor (M1), DC controller PCB Counter (CNT1), DC controller PCB E000 E001 E002 E003 E004 E010 E030

Jan 05, 2010 | Canon Office Equipment & Supplies

1 Answer

The Reebok Fitwatch 10S Calorie Counter


Yes when you are in time mode press the mode button 5 times this will be your calorie screen press the st/stp button to activate the calorie counter you will see in the bottom left corner it says CA ( meaning calories) and in the bottom right crn are the calories you are burning press the st/stp button again to stop then reset when you want to start again.Hope this helps can you help me? I keep pressing the sensor buttons and my heart rate does not appear what am I doing wrong ? Ive read my instructios inside out even returned the watch and got another but the same thing keeps happening ! Initial when I set the watch up it works then I just cant seem to get my heart rate to appear ????????? Thanks Nicole

Mar 24, 2009 | Reebok Fit Watch 10M Strapless Heart Rate...

3 Answers

How accurate are the calorie counters on treadmills and cardio equipment?


Here's what the Sole exercise equipment makers say about calorie counters on exercise equipment. it's from their E-95 users manual: "Calorie readings on every piece of exercise equipment, whether it is in a gym or at home, are not accurate and tend to vary widely. They are meant only as a guide to monitor your progress from workout to workout. The only way to measure your calorie burn accurately is in a clinical setting connected to a host of machines. This is because every person is different and burns calories at a different rate. Some good news is that you will continue to burn calories at an accelerated rate for at least an hour after you have finished exercising!"

Dec 01, 2008 | Endurance TF3i Folding Treadmill

Not finding what you are looking for?
Nordic Track Treadmill Motor Controller Mc5100dts-50w 37376 Pn 285703 - Logo

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nordic Track Exercise & Fitness Experts

Matt Olenzek
Matt Olenzek

Level 2 Expert

297 Answers

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

128 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Nordic Track Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...