Question about Canon Pixma MP450 All-In-One InkJet Printer

7 Answers

CANON PIXMA ERROR 5800

WHAT IS THE PROBLEM AND HOW DO I FIX IT?

Posted by on

7 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,559 Answers

The waste absorber is full ,Replace the pads
then if you still get the error,you can reset it by following the directions below.
(reset without replacing pads can cause damage)

1) Enter SERVICE MODE By pressing Menu-Scan-Copy-Scan
2) Enter NVRAM by pressing <--- or ---> then OK
3)SET ABS-M LEVEL TO 0
4)OK

Posted on Jan 28, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 6,966 Answers

Hi and welcome to FixYa,

Your described problem with a Canon Pixma MP450 indicates that the absorbent material that takes in the waste ink could no longer absorb further anymore waste ink. The waste ink if a result of cartridge/head initiation and most often when cleaning is done.

Corrective action is of course replacement of the waste ink pad. Although the reset procedure could be performed to 'trick' the printer to think that it was replaced. Steps involve are:

  1. You will turn off printer.
  2. retaining button Resume/Cancel (red triangle in the circle) press button POWER - indicator it will catch fire by green color.
  3. you will let go button Resume/Cancel, continuing to retain POWER.
  4. press button Resume/Cancel of 2 times, retaining POWER, after which you will let go all buttons.
  5. when indicator will be lit BY GREEN - press button Resume/Cancel of 4 times!
  6. you will turn off printer by button POWER.
Goodluck and thank you for using FixYa.

Posted on Jan 20, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Canon Master
  • 19,396 Answers

Error 5800 is waste ink full, depending on what Pixma model you have, there are different reset procedures.

See links below:

Canon Error 5800 Waste ink Full Pixma MP 130 - fixyourownprinter.com

Error 5800 on Canon Pixma MP170 - FixYa

Printer Repair And Service Tools: Canon Error 5800 Waste ink Full ...

Posted on Jan 28, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 679 Answers

1 press menu2 PRESS scan copy scan to enter service mode 
3 use > to go to NVRAM ACCESS
4 set ABS-M LEVEL TO 0
5 Set ABS P LEVEL TO 0
6 Set press STOP to EXIT

Posted on Jan 28, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,029 Answers

Its a waste ink error

Posted on Jan 20, 2009

  • 1 more comment 
  • Starnley Johnwells
    Starnley Johnwells Jan 20, 2009

    follow these steps
    1) Enter SERVICE MODE By pressing Menu-Scan-Copy-Scan
    2) Enter NVRAM by presing <--- or ---> then OK
    3)SET ABS-M LEVEL TO 0
    4)OK


  • Starnley Johnwells
    Starnley Johnwells Jan 20, 2009

    Canon Waste Ink Tank Reset Procedures
    try this

    Discharge of the code 5100
    1. Turn off printer.
    2. retaining button Stop/Reset (red triangle in the circle) press button POWER - indicator it will light up with green color.
    3. let go button Stop/Reset, continuing to hold POWER.
    4. press button Stop/Reset 2 times, while holding POWER button, after which you will let go all buttons.
    5. when indicator is lit BY Solid GREEN - press Stop/Reset 4 times! (this is the key)
    6.turn off printer by POWER button, then turn on.
    7. You should be set. If it didn't work, try it again, slowly. It WILL work!




  • Starnley Johnwells
    Starnley Johnwells Jan 20, 2009

    hope this helps

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Canon Master
  • 13,433 Answers

Waste ink absorber is full

the waste ink tank needs to be cleaned or replaced and then the printer needs the counter reset.

reset instructions
http://www.fixyourownprinter.com/forums/printer/52461


Posted on Jan 20, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

Welcome to Fixya! Try this. Unplug all Cables and Power from the Printer. Uninstall and Reinstall Printer Software, Restart your PC, Reinstall your Cables and Power, Run Software and Print a Test Page. Let me know where you are at then.

Posted on Jan 20, 2009

3 Suggested Answers

  • 1335 Answers

SOURCE: my canon pixma mp830 shows error code 5010. what

The scanner lock switch may be in the locked position. Lift the cover and check the slide switch located on the top front left. If this is not the problem, you will have to have a service center look at the problem.

Posted on Dec 19, 2009

SOURCE: Error 5800: waste ink

Clean or replace the absorber and reset the printer counter to clear the message.

Posted on Apr 30, 2008

  • 1 Answer

SOURCE: canon printer pixma mp110

My Pixma MP110 keep on displaying "CHECK PRINTER (5800)" Please have m to solve this problem

Posted on Mar 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does printer error code 5800 mean?


This is an ink overuse error. It may read 5B00 and not 5800.
No real easy fix as far as I know but this video might help. Good luck! https://www.youtube.com/watch?v=0waX_GF-h7U
This video might help

Dec 02, 2015 | Canon PIXMA Printers & Copiers

1 Answer

My Canon MX700 has 5800 error. How do I fix it?


you might have to uninstall the printer restart your computer then reinstall your printer
click start control panel administrative tools computer management device manager scroll to ports(COM&LPT) + to expand you should see a communication port and Ecp printer port

you might see a yellow? ! question exclamation mark or a red X this will mean you need to install a new driver for this device right click you will have options to update driver disable uninstall or select properties again you will have the similar options also you can troubleshoot the device
hope this helps you

Nov 15, 2011 | Canon PIXMA MX700 All-In-One InkJet...

1 Answer

Canon PIXMA iP 1500 does not print


Hi,
1 press menu
2 PRESS scan copy scan to enter service mode
3 use > to go to NVRAM ACCESS
4 set ABS-M LEVEL TO 0
5 Set ABS P LEVEL TO 0
6 Set press STOP to EXIT
Thanks

Thiru

Jun 17, 2009 | Canon PIXMA iP1500 InkJet Photo Printer

2 Answers

Error code 5800 for Pixma MP130. When try to get


you can try this:

Turn on the printer (MP130) and do the following:
1. Press MENU SCAN COPY SCAN to enter service mode
2. Use > to go to NVRAM ACCESS
3. Set ABS-M LEVEL to 0
4. Set ABS-P LEVEL to 0
5. Press STOP to exit

Done, hope it work.

May 30, 2009 | Canon PIXMA MP130 All-In-One InkJet...

3 Answers

Canon MX 308


How to reset canon MX 308 ??
Error Code 5800
Any Software to reseter this printer?

Feb 24, 2009 | Canon PIXMA MX310 All-In-One Printer

3 Answers

Error (5800)


Waste ink is full counter reset.

Sep 15, 2008 | Canon PIXMA MP130 All-In-One InkJet...

5 Answers

Canon printer pixma mp110


how can i reset canon pixma mp 110 tahnk you please help me

Jun 02, 2008 | Canon PIXMA MP210 Photo All-In-One Printer

Not finding what you are looking for?
Canon Pixma MP450 All-In-One InkJet Printer Logo

3,615 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Printers & Copiers Experts

kakima

Level 3 Expert

96372 Answers

old marine
old marine

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Canon Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...