Question about Gigabyte GA-8IE533 Motherboard

1 Answer

Emachine model W2888, wiring

I accidently unplugged the 3 connections coming from the front of the PC to the mother board. I believe they are for the LEDs and thr power button. Anyway can someone let me know the right pins to connect to?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

This is someone more suited for a trained technician, but you can look at the motherboard, where the pins were, and you should see markings like pwr +, pwr -, led +, led -, hdd_led, etc, you will also see markings on the cords that connect to the motherboard, with the same words, pwr+, pwr-, etc, you can try matching those up..

Posted on Jan 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I disconnected the wiring from the face cover to the motherboard on a emachine model T2984. how do the wires reconnect? three plugs red-white black- white bluu -white


you will need to down load the mother board connection chart if you connect them the wrong way round there is a chance that you may damage the board but mores to the point if the wires are usb support if you get this wrong you will destroy most usb items as current will flow up the data lines (bad times) wait untill you get it right (good times)

Jan 17, 2010 | Motherboards

2 Answers

Nothing get displyaed once pc on


try and find the installation manual for the exact model of system board and verify if the front panel connectors on the system board have been connected correctly. i suspect you might have inversed the power btn and power led cables. if this is not the case, then you might want to reset your power management settings in the BIOS setup.

Oct 05, 2009 | Intel Motherboard

1 Answer

I have an emachine t3104 and upgraded the memory the wires from the front of the case became un attached now I dont know where they connect on the motherboard they are black and whitebbgreen and white and...


That model has a MSI K8MM-V (MS-7142-010) motherboard. Mostly likely you knocked some of the computer case wire connectors off the motherboard. These connectors usually include things like the case speaker, indicator for your hard drive operating, etc.

You may want to do a websearch for the manual, which will show a detailed breakdown of these wire connections and how to reinstall them.

Aug 28, 2009 | Motherboards

1 Answer

Need picture of mother board for Emachine C2825


I've built a PC myself, each connector had text on it to say what it was and one arrow on it in relief, don't know wether that indicated plus or minus anymore.
Anyway, I recommend you just plug them in, and try to boot the PC. If it doesn't boot, switch the Power SW connector around, then it should boot. Do the same with the LED connectors, and it should work just fine!

Good luck,
Yannick.

Jul 13, 2009 | Intel D845GVSR Motherboard

1 Answer

Emachines computer not turning on


IS ALL CONNECTION CORRECT, TYPE IN

EMACHINE COMPUTER DOWNLOAD DRIVES
ENTER

SEE IF ANY OF THIS INFO CAN HELP YOU

THE MAIN SWITCH FROM THE PANEL ON THE FRONT OF YOUR COMPUTER DIDNT MATCH YOUR NEW MOTHERBOARD CONFIGURATION
START BY REMOVING ALL WIRES AND CONNECTORS EXCEPT POWER ONE, SEE IF SYSTEMS TURNS ON, THE POWER SWITCH MAYBE THE PROBLEM, RESET SWITCH, ANY EXTRA CARD YOU PLUG INTO YOU MOTHER BOARD
*********REMOVE ANYADD ON CARD ANY ADAPTER DEVICE ALSO,

ADD ONE WIRE AT A TIME UNTIL ALL WIRES ARE CONNECTED

CANDYMANCANDY

Jan 27, 2009 | E-Machines (308714) Motherboard

2 Answers

PROBLEM WITH AUDIO DEVICE


the front port wire is not connected to the mother board.please refix it .

Jan 13, 2009 | Motherboards

2 Answers

T3624 MB someone pulled off the 3 wire pairs to the front bezel. What's the pin out for the 2 leds & power on??


According to the internet, your computer has an Intel 845GV chipset motherboard. Intel tends to use a generic pattern for connecting the front panel connectors. A description can be found on intel's site.
If this doesn't solve your problem, comment back with the motherboard model number. Look on the board, it should be printed somewhere, and it should start with D845GV...something something...

Steven

Sep 17, 2008 | E-Machines (308714) Motherboard

Not finding what you are looking for?
Gigabyte GA-8IE533 Motherboard Logo

Related Topics:

243 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gigabyte Motherboards Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Tony

Level 3 Expert

2598 Answers

Are you a Gigabyte Motherboard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...