Question about Sportcraft Tx 455 Sportscraft Treadmill Controll Panel

1 Answer

Can the belt be tightened on my sportscraft treadmill

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Sportcraft Master
  • 12,223 Answers

Please see the video and fix it.
God bless you

Posted on Jan 07, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a sportscraft treadmill it come p. fine run for a few seconds and goes off. The screen had a 3 on it when it goes off. The fee seconds it does run it seems fine


7eef0c0f-9fee-4743-8c0c-d60deca9fbdb.gif1) tight and clean the upper and lower connector
2) tight and clean the ribbon cable for display board
3) adjust the Reed swtich , tight and clean and test for faulty or open
see the diagram attached.
4) lube the deck belt see the video.


God bless you

Nov 03, 2013 | Exercise & Fitness

1 Answer

My sportscraft treadmill stops and displays a 3 on the monitor,what would cause this?


please LUBE THE deck belt, this happen because the lack of maintenance. shut down.for protecting the electronic system
2)LUBE the rollers bearing too very well
3) test the input voltage motor, if there are the motor need repair.
4) adjus the REED swtich, see the diagram , clean it, an tight any connector, or plug.
God bless you
10_17_2012_12_30_48_pm.gif

Oct 16, 2012 | Exercise & Fitness

1 Answer

My sportscraft treadmill TX4.9 shuts down when it shows 3 on the speed


LUBE the deck belt,this happen because the lack of maintenance. may be is time to exchange the drive belt.
2) LUBE the rollers bearings. too
3) measure the input voltage motor, if there are the motor need repair
4) measure the output voltage board, for input voltage motor , if there are NOT the board is faulty. see the b. diagram attached, see my personal TIPS.
God bless you
10_12_2012_9_50_49_am.gif

Oct 11, 2012 | Exercise & Fitness

1 Answer

I have a Reebok treadmill. The belt stops while the motor continues while walking on it. What could be causing this to happen?


the drive belt is too loose. you need to tighten the belt that drives the front rolller, which drives the walking belt. depending on the type of treadmill there shoudl be a way you can do this by loosening the motor and adjusting that to tighten the belt. it could also be that the belt needs to be replaced and also could be the walking belt. you should try to tighten the walking belt first. that is at the end of the treadmill where you walk on it. there are two holes one on each side of the treadmill where teh belt goes back under the treadmill. there are allen key bolts that you need to tighten clockwise one turn then try the treadmill. if it doesnt tighten then turn another full turn. if not tight enough then it might be the drive belt. if you tighten the walking belt all the way then try to tighten the drive belt.

Jan 28, 2011 | Reebok Exercise & Fitness

1 Answer

Treadmill belt keeps slidding to the side


Here are two solutions one is to get the belt centered on the treadmill and the other is to tighten the belt.

There should be two bolts in the rear of the treadmill, one on each side. These bolts adjust the rear roller of the treadmill. The walking belt will always go to the side that is looser. To get the belt back on track, (if you can start the treadmill so the belt is running) tighten the bolt on the side that the belt has slipped to. Tighten the bolt a little bit at a time. If you tighten the bolt too much, then the belt will go to the other side.

To tighten the belt, start by locating the two bolts that adjust the rear roller (one on each side of the unit in the back). Run the unit at about 3 mph. Tighten the bolts a 1/4 turn at a time. Make sure that what you do to one side, you MUST do to the other side or the belt will get off center. After you tighten it 1/4 turn, check the belt to see if it is still slipping. If it is then tighten the belt 1/4 turn again. Continue until the belt does not slip, but do not tighten the bolts more than 2 full turns.

Apr 08, 2010 | RTO Image 15.0R Treadmill Walking Belt

1 Answer

I need to know how to tighten the belt


describe how to tighten the belt on a tx 400 sportscraft treadmill.

Dec 16, 2009 | RTO Exercise & Fitness

1 Answer

Treadmill tx400 wont work for llonger then 6 seconds


Sportcraft tradmill are very safe. First check and make sure there are no recalls on you unit. Do that on line or call Walmart where you most lickly got you treadmill. Try lubing you deck wich is under the belt. This is something that needs to be done to stop friction... Frition may have worn down the motor. Get back to me

Oct 10, 2009 | Exercise & Fitness

1 Answer

Bogs down


Sounds like either the belt is loose or the belt/deck need to be lubed.
To tighten the belt, start by locating the two bolts that adjust the rear roller (one on each side of the unit in the back). Run the unit at about 3 mph. Tighten the bolts a 1/4 turn at a time. Make sure that what you do to one side, you MUST do to the other side or the belt will get off center. After you tighten it 1/4 turn, check the belt to see if it is still slipping. If it is then tighten the belt 1/4 turn again. Continue until the belt does not slip, but do not tighten the bolts more than 2 full turns.
To lube the treadmill, use silicone spray and spray between the belt and deck on both sides. I hope this helps. Let me know if you have any other problems.

Feb 21, 2009 | Exercise & Fitness

Not finding what you are looking for?
Sportcraft Tx 455 Sportscraft Treadmill Controll Panel Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sportcraft Exercise & Fitness Experts

John

Level 2 Expert

125 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Sportcraft Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...