Question about Insignia 200W Stereo Receiver

2 Answers

Insignia nsr2000 on/off problem.

I have a problem.i turn it on and it goes right off.it won`t stay on.i unplugged it and waited.plugged it back in.same problem.hit the power.1 sec later goes off.thank you .

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Had the same problem... turns out the copper on my red and black speaker wire (on the speaker, not receiver end) was touching - causing my receiver to go to standby (self-preservation probably lol). i pulled the wires further apart so the copper ends weren't touching and that solved it.

Posted on Oct 24, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Call 614 776 3355 - BEEPS COMPUTER CLINIC.

Posted on Feb 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stereo receiver turns on then shuts right.back off


It sounds like the safety circuitry is being activated to prevent a more serious hazard. The problem is most likely located in the speaker wiring plugged into the back of the unit.

If you unplug everything on the back, all of the wires going into and out of the receiver, and it still does this, then there is a big problem inside the stereo's circuitry. It may have a blown amplifier chip, and will require an electronic technician to repair it.

If it stays on with everything unplugged from the back, then if you plug each item back in, one by one, you will discover which item is the culprit.

Aug 30, 2015 | Audio & Video Receivers

1 Answer

Receiver keeps going to standby


I don't know about the newer receivers but this sounds like an arching OFF/ON power switch that was a problem on Pioneer receivers years ago. I would bypass the switch and see what happens.

1. Unplug unit from wall.
2. Jumper two wires going to off/on switch using alligator clip with insulated boots on clips.
3. Plug amplifier into disconnected circuit breaker/fuse protected AC strip.
4. Plug AC strip into wall outlet, turn AC strip switch ON and see if problem disappears.

Feb 20, 2013 | Insignia 200W Stereo Receiver

1 Answer

Unplugged tv for storm, plugged it back in now it trys to turn on but won't


plug in a bed side light and see is it working and if it is not then the storm has damaged the tramsformer supplying your house

Aug 08, 2012 | Samsung Hlr5667w 56-inch Dlp Hd Tv

1 Answer

How do i reset dennon avr 1000


turn it off and unplug from outlet, wait 1min

then press audio and video buttons together on right hand side of unit

hold these and turn plug it back in to outlet
wait until display flashes every second then release buttons
turn on unit to reset
note all settings will be factory default.

Hope this helps
Thanks for using FixYa

Jun 12, 2010 | Denon AVR-1200 Receiver

1 Answer

My receiver stays in standby mode and will not power up. It will turn off but will only turn on back to standby.


Unplug the unit from power and wait at least five minutes. Plug it back in and try it. If that does not work check your operating manual to see if there is a reset that can be performed. This would do a "factory reset" which would hopefully solve the problem. Good Luck!

Nov 08, 2009 | Harman Kardon AVR 240 Receiver

1 Answer

Lightning Last Night Nocked The Receiver Out.


leave unpluged overnight. usually capacitors hold charge and will release slowly. try that if doesnt work powersupply is bad.

Jun 03, 2009 | Yamaha RX-V861 Receiver

1 Answer

Receiver stays on standby mode


Receiver either just stuck or held or having problem in amplifier output area.
Try to unplug it from AC outlet for couple of minutes and replug back in and power up, if works, fine and if does not, take it to local repair shop as it might requires some parts replacement in amplifier out area.

Feb 10, 2009 | Insignia Audio & Video Receivers

1 Answer

Receiver shuts down and will not turn back on untill you unplug and plug back in


Nope. sorry to burst your bubble but your problem is pretty common on this unit. Its bad capacitors in the power supply and probably not worth repairing in a repair shop. since this is a solid state reciver, there are no user replaceable parts inside.

Sep 24, 2006 | Harman Kardon AVR 235 Receiver

Not finding what you are looking for?
Insignia 200W Stereo Receiver Logo

Related Topics:

1,059 people viewed this question

Ask a Question

Usually answered in minutes!

Top Insignia Audio & Video Receivers Experts

Lawrence Oravetz

Level 3 Expert

7686 Answers

carlosacns53

Level 1 Expert

41 Answers

The Knight
The Knight

Level 3 Expert

68352 Answers

Are you an Insignia Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...