Question about Estate Dryers

Open Question

Year model of Estate Dryer Model # EED4400WQo

What is the year model

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Illeagle
  • 525 Answers

SOURCE: No heat Estate Dryer model # TGDL400WW1

Warning! To avoid personal injury or even death, always disconnect your appliance from its power source--that is, unplug it or break the connection at the circuit breaker or fuse box--before you do any troubleshooting or repair work on your appliance. Also, because some components may have sharp edges, use caution while working on your appliance.
Below is a link to common solutions that will help you with parts and diagnostic procedures that are specifically tuned to your manufacturers data plate information.
It provides exploded view imagery, belt routing diagrams, parts imagery and function, parts ordering and shipping information, error code details, just about anything you need to get your appliance up and running again.


Tip: Always provide the complete information provided on the manufacturers product information data tag, located on the unit, and not in the user’s manual. This will help you acquire a more accurate and expeditious response to your complaint.
http://www.repairclinic.com/0088_8_1.asp#Level1_14

If your dryer doesn't heat, check these:

Temp. Switch, make sure a positive selection is made.
Igniter
Gas valve coils
Thermal fuse
Igniter Modern gas dryers use an electric igniter to ignite the gas from the gas valve. When it's working properly, the igniter glows bright orange. When it burns out, the dryer tumbles but there's no heat because the gas can't ignite. When the igniter burns out, you need to replace it. If the igniter is held by a tension bracket, you very well may need to replace the bracket too.

The igniter is inside the dryer housing, near the bottom front, usually in a cone-shaped metal tube (the force cone). It's about 2 inches long. It's mounted to the far end of the burner tube, and it has two wires attached to it--or to the tension bracket, if there is one.

Gas valve coils Watch the igniter. Does it glow bright orange, then shut off without igniting the gas? (When the gas ignites there's a large blue flame.) If so, there may be defective coils on the gas valve. Mounted on the top of modern gas valves, there are black electrical coils. The coils, when energized, open the gas valve. If one or more of the coils are defective, the valve doesn't open and the gas cannot ignite. Because it's often difficult to properly test the coils, it's usually best to replace both (all) of them at the same time.

Thermal fuse On many dryers, there's a thermal fuse (a heat-sensitive fuse that blows if the dryer overheats) mounted to the exhaust duct inside the back cover panel. The fuse is about an inch long. It's usually embedded in black resin and mounted in a white plastic housing.

If the fuse has blown, it has no continuity. When this happens, your dryer either just stops heating, or it doesn't work at all. Be sure to inspect the venting/heating system before replacing the fuse to put the dryer back into operation. (You can't re-set this type of fuse.)

If my assistance helped resolve this issue, please show your appreciation by rating how effective my advice was in resolving this issue.
Thank you,
Dave E. (Illeagle)

"Your satisfaction is my personal reward"

Posted on Jul 04, 2008

jsrock516
  • 5911 Answers

SOURCE: CANT FIND MODEL OR SERIAL NUMBER ON DRYER

There should be a nameplate along the door opening. This is normally where Whirpool puts their information. Just open the door and look along the door or door frame opening. The nameplate data can also be located along the back of the operator console on some models. Let me know if you still can't find it. I hope this helps.

Posted on Nov 11, 2008

Maytag317
  • 1136 Answers

SOURCE: gas dryer runs but no heat

Hi, Remove the little cap on the front panel lower left corner and start the dryer. Look into the hole and see if the ignitor glows (5 - 10 seconds)
If the ignitor does not glow, try this: Normal 0 UNPLUG the dryer! Remove the rear panel of the dryer and locate the fuse. It is white and ¼” wide and 3” long. It is located on the blower housing. Remove the wires and check to see if it has continuity. If it does not, you need to replace it.
If the ignitor glows and then shuts off before you see a flame, try this:
Normal 0 UNPLUG the dryer. This model you need to remove the two screws under the lint screen. Now use a flat blade screw drive and insert it in the gap between the top and the front panel and pry the top up. Now locate and remove the screws on the inside of the front panel in upper corners. The front should lift off. You will see the two black coils on the gas valve. When you remove the three wire coil, make sure the sleeve inside it gets put back on the post the coils slides onto. I know this is a lot of info but, it's the most popular problems.
Please let me know if this help or if I can assist you further.

Vic

Posted on Jun 01, 2009

  • 1218 Answers

SOURCE: No heat to dry clothes. Dryer is 4.5 years old.

By far, on that machine the "thermal fuse" accounts for more than 50% of all heating problems.

Unplug machine and remove back cover. On the air chute in the middle back of the dryer you will see a small narrow bakelite device with 2 wires connected to it. It is held in with 1 screw.
You will need an ohm meter to test it, or remove it and have an
appliance parts house test it for you. If bad replace.
Whirlpool part #3392519.
The second common problem on that dryer is the heating element and can be checked with an ohm meter as well.

On rare occasions one side of the 230 volt supply is out.
The side running the motor is o.k. but the heater side has lost power.

Caution: your dealing with 230 volts here. remove plug receptacle cover and check with a volt meter for power.

Posted on Nov 03, 2009

heatman101
  • 43501 Answers

SOURCE: I have a Whirlpool Estate

Hi, If you are having problems with your gas dryer not heatingthe most common problem is that the ignitor goes bad. Even though it glowssometimes it is still not working properly. if you dryer is gas check out this gas no heat tip.... If you have an electric dryer, you can have many differentthings that can go wrong causing the dryer not to heat. check outthis electric no heat tip...

heatman101
';';
';

Posted on Jul 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Estate dryer Model tgds840pq0 isn't completely drying the clothes on auto setting


The sensor that detects moisture may be covered with lint

Jun 06, 2016 | Estate Dryers

1 Answer

My estate dryer model #eed4400wqo


I suppose you want to clean the lint vent to outside. Clean out the filter first by removing the manual filter and pulling off all stuck lint. Try this link to clean the vent:

How to Clean Clothes Dryer Vent

Feb 12, 2015 | Estate Eed4400wq 29 6.5 cu. Ft. Electric...

1 Answer

How do you change a dryer belt


That is the same model dryer I bought for my parents eight years ago. You will have to contact Whirlpool for a repair guide.

Apr 22, 2012 | Estate TEDS840JQ Electric Dryer

1 Answer

Estate dryer tensioner loose while installing belt


Go to www.appliancehelponline.com/servicemanual.html there is a video that will show you how to replace it. It may be a different model but the process will be the same. You can also enter in your model # for diagrams and illustrations. Not all models are available. All parts come with installation instructions.

Apr 28, 2010 | Estate TEDX640JQ Electric Dryer

1 Answer

Drum will not turn


YOUR BELT ON YOUR DRYER IS BROKEN. THAT IS WHY YOUR DRUM WON'T SPIN. YOU CAN BUY A NEW BELT FOR YOUR DRYER AT ANY PLACE THAT SELLS APPLIANCES.
RODNEY

May 15, 2009 | Estate TEDS740JQ Electric Dryer

1 Answer

Timer not working on estate model TGDS840JQ1


Try first tripping the circuit breaker for ten minutes and see if this reset the board.

Here is the part: PS394424

Check also the connector:PS345626

Here all diagrams for your appliance.

Parts must be tested before replacement.

May 07, 2009 | Estate TGDX640JQ Gas Dryer

1 Answer

CANT FIND MODEL OR SERIAL NUMBER ON DRYER


There should be a nameplate along the door opening. This is normally where Whirpool puts their information. Just open the door and look along the door or door frame opening. The nameplate data can also be located along the back of the operator console on some models. Let me know if you still can't find it. I hope this helps.

Nov 11, 2008 | Estate TEDX640JQ Electric Dryer

1 Answer

Dryer drum will not turn


Try pushing start button while turing drum clock wise and see if drum will start spinning, sounds like bad start winding or relay

Sep 17, 2007 | Estate EED4300SQ Dryer

Not finding what you are looking for?
Dryers Logo

Related Topics:

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Estate Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3072 Answers

Terry Schneider

Level 2 Expert

177 Answers

Are you an Estate Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...