Question about Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Fit new door seal

How do I fit door seal on hotpoint aquarius WF000

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Hotpoint Master
  • 662 Answers

For most front-loaders:
Plug off the wall mains. Remove the plastic clamp holding the seal to cabinet & peel off the cabinet. Push downwards on the seal close to the tub & the seal will come off - it's just held by a spring on the periphery.
Lubricate the slot which fits over the tub with washing-up fluid. Starting at the top, press the seal so the flange of the tub enters the slot on the seal. Work your way round the using thumbs to force the slot on the tub flange. When slot is on the flange all way round, fit the spring which holds it on. The spring goes into a slot on the outside of the seal. This is quite difficult and you may need another pair of hands. Fit the outside of the seal to the cabinet - this is easy and fit the plastic clamping ring.
Test for leaks before using. Use rinse to test as the water level is higher.
(There is no glue anywhere, only clamps,etc)

Pl rate me nice for the free help!

Posted on Jun 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just fitted a new door interlock on my hotpoint but the close door msg keeps appearing. Any ideas?


Could be a weak door spring, or worn or cracked catch, meaning that it is not latching in properly, try activating the door lock with a screwdriver or similar if you can, if still no joy, then could be a board or cumminication prob between boards
please rate my solution.
Thanks.

Oct 10, 2009 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Hotpoint WF645 : Do I Need special tool to clamp


not worked on this model.but hotpoint are usually eaSY. no special tools.but i found it easier to take the front of the machine and work at it that way about 1 hour

Jun 30, 2009 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Hotpoint Aquarius


I have a hotpoint aquarius washer/drier. I don't know if this will solve your problem but I know with mine, this almost always happens, the only way I can get it to start is by firmly pushing the door a few times around where the lock is, once I hear a little click inside it will start ok. I presume its because it wont start as it isn't registering that the door is closed, the only time it does not do this is if I literally slam the door really hard. Hope this helps you!

Sep 13, 2008 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Door seal


switch off from mains
remove outer clamp holding door boot to cabinet and peel off door boot.
remove work top
there is a clamp holding door boot to tub. undo clamp and pull door boot away
lubricate slot in door boot that goes on to the lip of the tub using washing up fluid
starting at the top, insert lip of tub into slot in door boot. working both ways round, push door boot onto lip
fit outer clamp
push door boot on to lip of the cabinet and fit clamp.
test for leaks on a rinse cycle (water level is higher) water will be a bit foamy till washing up fluid is washed away
easy job but needs a bit of patience so go for it

Sep 07, 2008 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Hotpoint Aquarius WF440 Repalce Door Seal


no need to remove front panel
remove clamp that holds boot to cabinet and peel away boot
take top off
undo clamp that holds boot to tub and pull boot off
lubricate slot in new boot that goes on to lip of tub
starting at top, insert slot onto lip of tub and work your way round in both directions pushing slot onto lip
refit clamp
push door boot onto lip of cabinet and refit outer clamp
test on rinse cycle for leaks (water level is higher
water will be a bit foamy till fluid is washed away

Sep 06, 2008 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Replacing door seal


Try washing the seal with jiff and a scouring pad in warm water.Depends on how well it is ground in.
You may have to replace with new seal.

slimjim1

Nov 25, 2007 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Door seal


i will tell u step by step 1)open the door undo the clamp that holds the front of the seal on it is around the lip push door seal back so its out of your way into the drum 2)take the lid of look to the front were your seal is fastened onto the outer drum this is held into place with a screw clamp unscrew it and u should be able to ease the door seal of from around the drum reverse these actions to replace the new 1 i have sent these instructions too 3 other people they have found these instructions easy to follow and do

Jun 24, 2006 | Hotpoint Aquarius WF000 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WF000 Front Load Washer Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...